Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Operating Instructions
Solar Wall Light PIR Sensor 4000 K 2000 lm
Item No. 2336767
Intended use
This is a wall mounted light with motion sensor. It
has a non-removable battery that is charged by the
integrated solar panel.
The product is intended for outdoor use. It has an
ingress protection rating of IP65 and is protected
from dust and low-pressure water spray from all
directions.
For safety and approval purposes, you must not re-
build and/or modify this product. If you use the prod-
uct for purposes other than those described above,
the product may be damaged. In addition, improper
use can result in or other hazards. Read the instruc-
tions carefully and store them in a safe place. Make
this product available to third parties only together
with its operating instructions.
This product complies with the statutory national and
European requirements. All company names and
product names are trademarks of their respective
owners. All rights reserved.
Delivery content
•
Product
•
Mounting bracket
•
Bracket screw
•
Switch pin
•
2x wall plugs
•
2x mounting screws
•
Operating instructions
Up-to-date operating instructions
Download the latest operating instructions at
www.conrad.com/downloads or scan the QR code
shown. Follow the instructions on the website.
Explanation of symbols
The symbol with the exclamation mark in
the triangle is used to indicate important
information in these operating instruc-
tions. Always read this information carefully.
This product is constructed according to
protection class III.
Safety instructions
Read the operating instructions
carefully and especially observe
the safety information. If you do not
follow the safety instructions and
information on proper handling in
this manual, we assume no liability
for any resulting personal injury or
damage to property. Such cases will
invalidate the warranty/guarantee.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights in-
cluding translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represents the technical status at the time of printing.
Copyright 2021 by Conrad Electronic SE.
a) General information
•
The device is not a toy. Keep it out of the reach
of children and pets.
•
Do not leave packaging material lying around
carelessly. This may become dangerous playing
material for children.
•
Protect the appliance from extreme tempera-
tures, strong jolts, flammable gases, steam, and
solvents.
•
Do not place the product under any mechanical
stress.
•
If it is no longer possible to operate the product
safely, take it out of operation and protect it from
any accidental use. Safe operation can no longer
be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor
ambient conditions or
- has been subjected to any serious transport-
related stresses.
•
Please handle the product carefully. Jolts, im-
pacts or a fall even from a low height can dam-
age the product.
•
Consult an expert when in doubt about the op-
eration, safety, or connection of the appliance.
•
Maintenance, modifications, and repairs must
only be completed by a technician or an author-
ised repair centre.
•
If you have questions which remain unanswered
by these operating instructions, contact our tech-
nical support service or other technical personnel.
b) Rechargeable battery
•
The rechargeable battery is permanently built
into the product and cannot be replaced.
•
Never damage the rechargeable battery. Damag-
ing the casing of the rechargeable battery might
cause an explosion or a fire!
•
Never short-circuit the contacts of the recharge-
able battery. Do not throw the battery or the
product into fire. There is a danger of fire and
explosion!
•
Charge the rechargeable battery regularly, even
if you do are not using the product. Due to the
rechargeable battery technology being used,
you do not need to discharge the rechargeable
battery first.
c) Installation
•
When drilling or tightening screws, make sure
there are no cables, wires, or pipes located un-
derneath the surface.
•
Inadvertently drilling through electric cables
can cause life-threatening electric shock!
Disposal
Electronic
devices
are
recyclable
waste and must not be disposed of in
the household waste. At the end of its
service life, dispose of the product in
accordance with applicable regulatory
guidelines.
You thus fulfill your statutory obligations and contrib-
ute to the protection of the environment.
*2336767_v3_0121_02_dh_m_en
Installation
Important
•
Check if the screws are suitable for the mounting surface material. Use the wall plugs if neces-
sary. If in doubt consult a professional.
•
Select a location where the solar panel receives the most sunlight.
•
Do not place the product near other light sources such as streetlights. This will prevent the sen-
sor from activating.
a) Motion detection angle
120°
b) Mounting
1. Screw the bracket to the product (2).
2. Mark a spot on a surface
2
3. (If needed) Drill a hole for the wall plug.
1
4. Insert the first screw. Leave some of the screw head protruding
and then hang the product (1).
5. Make sure the product is vertically aligned.
6. Mark the position for the bracket screw hole.
7. Drill a hole for the wall plug if needed
8.
Hang the product from the first screw.
9. Secure it with the second screw (2).
Operation
Important
•
Keep the panel clean to maximize charging efficiency. See section "Care and cleaning".
•
If the solar panel is not exposed to enough sunlight:
- Conserve battery by reducing the power consumption during the night by selecting "Mode 2".
- The product may run out of battery and will not switch on. If this happens place it under bright
sunlight to recharge.
1. Before first use, place the panel under bright sunlight for at least 5 hours
to charge the battery.
2. Use the switch pin to press and hold the multifunction button for 1.5 sec-
onds to switch the power ON/OFF.
3. Press the multifunction button to switch modes:
- Mode 1: LED ON (50 lm). When PIR sensor is triggered LED gets
brighter (2000 lm).
- Mode 2: LED OFF (0 lm). When PIR sensor is triggered LED turns
ON (2000 lm).
- Mode 3: LED constantly ON (50 lm) LED turns OFF at sunrise (≥100 lux)
Motion sensor
The LED will stay on 10 seconds after the motion stops.
Care and cleaning
•
Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as they can
cause damage to the housing and malfunctioning.
•
Clean the product with a dry, fibre-free cloth.
•
Use a cloth moistened with water if needed.
Technical data
Input voltage/power .............................. 4.86 V 1 W (from solar panel)
Solar panel type .................................... Epoxy Mono-Crystalline
Rechargeable battery ........................... Li-ion 3.7 V, 4000 mAh
Recharge time ...................................... 20 hours at 10000 lux
Operating time ...................................... max. 7 nights (8 hours/night)
Ingress protection ................................. IP65
Protection class .................................... III
LED ....................................................... 39 pcs
Colour temperature ............................... 4000 K
Light modes .......................................... Mode1: 50 lm + PIR (2000 lm), Mode 2: 0 lm + PIR (2000 lm)
Mode 3: 50 lm until sunrise (≥100 lux)
PIR sensor ............................................ Detection angle: 120º, Detection distance: 5 m
Installation height .................................. 2.5 - 3 m
Operating/storage conditions ................ -20 to +60 ºC, ≤75 % RH (non condensing)
Dimensions (W x H x D) ....................... 107 x 149 x 114 mm
Weight .................................................. 370 g
Motion detection:
•
Works best when the subject
walks across the sensor.
•
Does not work well behind glass.
2.5 - 3 m above ground level.
Werbung
