Renkforce 1337093 Bedienungsanleitung Seite 2

G Operating instructions
Raspberry Pi RS232 board
®
Item no. 1337093
Intended use
The product extends your Raspberry Pi
It is designed for connection to TX and RX GPIO outputs of Raspberry Pi
No driver installation needed.
Power is supplied via your Raspberry Pi
Carefully read this entire instruction manual which contains important information
about operation and use. Observe all safety instructions!
Package contents
• RS232 board
• Connection cable
• Operating instructions
Safety instructions
D amage due to failure to follow these operating instructions will void the
warranty. We do not assume any liability for any resulting damage!
W e do not assume any liability for material and personal damage caused
by improper use or non-compliance with the safety instructions. In such
cases, the warranty will be null and void!
Dear customer,
The following safety instructions and hazard warnings are intended not only
to protect your health but also to protect the device. Please read the follow-
ing points carefully:
• When touching or connecting the board, appropriate safety precautions
against static charge should be taken (e.g., earth connection, insulating
support, etc.).
• The product is only suitable for dry, enclosed indoor areas. It must not get
damp or wet as this would damage it.
• Protect the product from cold, heat, direct sunlight, dust and dirt.
• Handle the product with care; it can be damaged by impacts, blows, or
accidental falls, even from a low height.
• The product is not a toy and it should be kept out of the reach of children.
Position the product so it is out of the reach of children.
• Do not leave packaging material carelessly lying around, since it could
become a dangerous plaything for children.
by one serial RS232 port.
®
.
®
or 4-pin connector.
®
Connection and start-up
• First of all, fasten the converter board, if possible, to your Raspberry Pi
housing, where you want to install it.
In any case, make sure especially that the converter does not cause a short
circuit (e.g., through contact with your Raspberry Pi
• If your Raspberry Pi is switched on, first switch it off, disconnect and remove the
®
voltage supply.
• Connect the 4-pole plug of the
connecting cable included with
the 4-pole terminal strip of the
RS232 board.
Please pay attention to the cor-
rect allocation. Orientation of
the plug on the board should be
like on the right figure.
(VCC = red (Pin1 from right) =
5 V/DC; TX = green (Pin2 from
right) = data lines; RX = brown
(Pin3 from right) = data lines;
GND = black (Pin4 from right) =
earth)
• Connect the 5-pole plug of the connecting ca-
ble included with the GPIO connectors of your
Raspberry Pi .
®
And again, pay attention to the correct allo-
cation. Orientation of the plug on the Rasp-
berry Pi should be about the same as on the
®
right figure.
(red = Pin2 (extreme left on fig.) (5 V/DC);
black = Pin6 (earth); green = Pin8 (GIPO14,
TXD0 (UART)); brown = Pin10 (GIPO15, RXD0
(UART))
• The RS232 board will be automatically recognized and installed by your Raspberry
Pi . An external driver is not necessary.
®
Depending on the operating system, it may be necessary to register and configure
the port in the operating system first.
Disposal
Electrical and electronic equipment do not belong in the regular household
waste.
Dispose of the waste product in accordance with the applicable legal regu-
lations.
Technical data
Power supply ...................................... through 4-pole connector
Operating voltage............................... 5 V/DC, (2.7 - 5.25 V/DC)
Supported Operating Systems ......... Windows
Connectors .......................................... 9-pole RS232; 4-pin connector
Max. baud rate ................................... 320 kbps
Dimensions (L x W x H) ..................... 48 x 42 x 17 mm
Weight .................................................. 14 g (only the board)
Operating conditions ......................... 5 °C to +50 °C; 20% to 80% relative humidity
Storage conditions............................. -25 °C to +70 °C; 15% to 90% relative humidity
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent
the technical status at the time of printing.
© Copyright 2015 by Conrad Electronic SE.
)!
®
XP, from SP1 (only 32 bit), Windows
®
Vista™, Windows 7, Windows 8, Windows
® ®
(32 and 64 bit); Windows RT, MacOS, Linux
®
or to the
®
8.1
®