Operating The Device; Adjusting / Operating The Device - mantona Turnaround 360 Advanced 3 Gebrauchsanleitung

5. Operating the device

5.1 Inserting the battery, Setup
1. Insert 4x AA batteries or rechargeable batteries into the pan head and mount
or set up the pan head where desired.
NOTE
Make sure that your devices are held securely.
Only mount the device on a tripod that is designed for the weight and dimensions
of the device. See section 12.
When tightening the screw connection between the camera and the turntable, be
sure to hold on to the turntable and not the base. Otherwise you could damage
the gearbox.
For proper pans, you should always mount the camera directly on the pan head.
However, it is also possible to mount a tripod head on the pan head and then the
camera on the tripod head for various effects. For example, the camera can be
rotated mounted askew or horizontally.
5.2 Mounting the recording device:
Attach your recording device to the Turnaround 360 Advanced 3 turntable with
the 1/4 inch connection thread, for example a DSLR, mirrorless system camera,
compact camera, smartphone, action cam or any other camera.
ATTENTION
Mind the maximum load capacity of the turnaround head.
See section 12.
ATTENTION
Make sure that the tripod is standing firmly with the mounted device so that it will not
tip over or slip. Ensure the device and the equipment used are secure and stable.

6. Adjusting / operating the device

6.1 Switch on the device
Turn on the pan head by switching the button [5] to "ON".
6.2 Setting the rotation:
The pan head can rotate either a specified angle in a specified time or conti-
nuously at a specified speed. You can set the angle in 10° increments.
20
6.3 Continuous rotation:
Continuous rotation is indicated by "---" in the "Degree" display.
There are 7 different speed settings.
"01": rotates once every 48 seconds (fastest speed achievable)
"02": rotates once every 5 minutes
"03": rotates once every 10 minutes
"04": rotates once every 20 minutes
"05": rotates once every 30 minutes
"06": rotates once every 1 hour
"07": rotates once every 2 hours
6.4 Rotation by angle:
To program a pan, you need to set the desired angle in degrees, the time in
which this angle should be panned and the direction of the pan, clockwise or
counterclockwise.
Note that not every rotation can be achieved, as the pan head has a top speed of
one degree per 136 milliseconds. The device will not allow incompatible settings.
Setup:
By pressing the "SET" button [3] one time, the rotation degree display will blink. Set
the desired degrees of panning by pressing the increase [1] or decrease button [2]
by increments of 10°.
For continuous 360° rotation, set the counter to "---". By holding the increase [1] or
decrease button [2], you can change the setting swiftly. The continuous rotation speed
shows up in the „Degree" display if you go higher than 360°. Press the „SET"
button [3] and then use the increase [1] or decrease button [2] to choose the desired
speed for continuous rotation.
By pressing the "SET" button [3] for the second time, the rotation time display will
blink. Set the desired time of the pan by repeatedly pressing or holding the
increase [1] or decrease [2] button.
By pressing the "SET" button [3] for the third time, the rotation direction will blink.
Choose the desired direction by pressing the increase [1] or decrease [2] button.
You can cycle through your settings by pressing the "SET" button [3] repeatedly.
To confirm and exit, Press the "Start/Stop" button once.
6.5 Starting the pan
Press the „Start/Stop" button [4] to start the pan
6.6 Stopping the pan
Press the „Start/Stop" button [4] to stop the pan.
21