Chicco We Gebrauchsanleitung Seite 14

must be fastened at all times.
To make sure that the belts are fastened properly to the anchoring
points, after placing your child inside the stroller, pull the end parts
of the belts firmly.
ADJUSTING THE BACKREST
The backrest can be adjusted to different positions.
6. To lower the backrest use the rear adjustment system by pushing
on the button and pulling the backrest down to the desired posi-
tion (Fig. 6). On the other hand, to lift the backrest, pull the strap
upwards (Fig. 6A).
WARNING: The child's weight can make these operations more
difficult.
REAR BRAKES
The rear wheels have linked brakes, which can be applied simulta-
neously on both rear wheels by using the support tube.
7. To activate the brakes, press down on the pedal located centrally
(Fig. 7). To release the brakes, press the pedal in the opposite di-
rection (Fig. 7A).
SUN CANOPY
The canopy is already installed on the stroller.
8. To open and adjust the canopy use the front arch (Fig. 8). The
hood can be extended by opening the zipper (Fig. 8A-8B).
9. Should you need to remove the hood from the stroller, remove
the fastening clip from the tube (Fig. 9), release the rear arch from
the plastic pins and pull it out (Fig. 9A). Complete the operations
by removing the Velcro on both sides (Fig. 9B) and the two but-
tons on the back (Fig. 9C). To mount the hood again, carry out the
operations described above in the opposite order, positioning the
fastening clip close to the handle joint (Fig. 9D).
ADJUSTABLE LEGREST
The legrest can be used in 2 positions.
10. To use the leg rest in a horizontal position, move the metal sup-
port forward (Fig. 10-10A). To lower it, return the support to its
original position.
FITTING AND REMOVING THE STROLLER LINING
11. REMOVING THE SEAT LINING
Remove the hood as described in paragraphs 8-9.
Remove the bumper bar.
Release the legrest adjustment rod from the front tubes and remove
the rod from the fabric pocket. (Fig. 11A and Fig.11B)
WARNING: Keep out of the reach of children.
Release the snap button located beneath the seat. (Fig. 11C)
Remove the fabric slots from the plastic pins (Fig. 11D). Repeat with
the slots beneath the backrest (Fig. 11E).
Remove the two fabric fins from the rails on the two lateral tubes.
(Fig. 11F)
12. REMOVING THE BACKREST
Remove the padding of the crotch strap if present.
Remove the backrest adjustment strap from the two rings on the
side flaps of the fabric. (Fig. 12A)
Open the zip on the upper end of the backrest and pull out the
plastic panel, taking care to correctly remove the six straps on the
side and lower part of the fabric and the crotch strap (Fig. 12B and
Fig. 12C).
13. FITTING THE BACKREST PANEL IN THE FABRIC AGAIN
Fit the plastic panel completely into the fabric pocket also helping
yourself from the inside and pull out the straps fastened to the pla-
stic panel through the fabric slots. (Fig. 13A and Fig.13B)
Close the zip at the top of the backrest.
Pull the crotch strap out of the relevant fabric slot on the seat. (Fi-
gure 12C)
FITTING THE STROLLER LINING
Fit the fabric lining back on the stroller by repeating the steps in-
dicated in the paragraph "removing the seat lining" in the opposite
order.
FOLDING THE STROLLER
WARNING: When opening or closing the stroller, make sure that
your child or other children are at a safe distance.
WARNING: Make sure that during these operations the moving
parts of the stroller do not come into contact with your child.
WARNING: Before closing the stroller, ensure that the storage bas-
ket is empty.
The stroller has a closing device that can be used with one hand.
14. To fold the stroller, press the button "A" behind the handle while
pressing the button "B" (Fig. 14); push down on the handle and
the stroller will close automatically. The stroller will lock itself in
the closed position. When closed, the stroller stands on its own
(Fig. 14A-14B).
ACCESSORIES
WARNING: The accessories described below may not be included
in some product versions. Carefully read the instructions for the ac-
cessories that came with the model you have purchased.
SHOULDER STRAPS AND CROTCH STRAPS
The stroller is fitted with padded shoulder straps and a soft crotch
strap to ensure the safety and comfort of your child.
15. For assembly, insert the shoulder straps in the buckles (Fig. 15)
and the crotch strap in the relevant padding (Fig. 15A).
WARNING: Adjust the waist belt if necessary by pressing on the
buckles.
WARNING: To guarantee the safety of your child, the safety harness
must always be fastened.
CARRY BAG
The stroller features a bag/backpack with handle and adjustable
shoulder straps.
RAIN COVER
16. To fit the rain cover, fasten the Velcro straps around the stroller's
frame, in the positions shown in fig. 16 (the steps must be re-
peated on both sides of the stroller).
When you have finished using the rain cover, allow it to dry properly
if it is wet.
WARNING: The rain cover cannot be used on the stroller without
the hood being extended, as it may cause suffocation.
WARNING: When the rain cover is fitted on the stroller, never leave
it exposed to direct sunlight with your child inside, as the tempera-
ture will rise considerably.
USING THE CAR SEAT ON THE STROLLER
On the Chicco WE stroller it is possible to fit the following elements,
which can be purchased separately:
• Kaily car seat
• Kiros i-size car seat with Fast In fastening
All car seats for use on the stroller require the special adaptors sold
separately.
WARNING: FOR THE ASSEMBLY AND/OR USE OF THE ITEMS
LISTED ABOVE, REFER TO THE RELEVANT MANUALS.
SOFT CARRYCOT MOUNTING AND REMOVAL FROM THE
STROLLER
The Chicco WE stroller is compatible with the Chicco Soft Carrycot.
To attach the carrycot to the stroller, remove the bumper bar, com-
pletely lower the backrest and place the legrest in the horizontal
position.
17. Turn the rod under the carrycot base until it is completely open
(Fig. 17-17A); hold the handles in the transport position and
place the carrycot on the stroller with the foot area facing the
handle of the stroller (Fig. 17B).
18. Attach the carrycot to the stroller's frame using the appropriate
straps. The carrycot has two straps with a buckle on each side. Wrap
the straps around the tube of the stroller in the positions shown
in Figure 18. The upper strap must first be inserted into the fabric
loop on each side of the stroller (Fig. 18A). After wrapping the straps
around the tube, close the buckles (Fig. 18B), pull the straps until
14