Troubleshooting Guide; Accessories; Environmental Protection - Metabo RM 36-18 LTX BL 46 Originalbetriebsanleitung

en ENGLISH

10. Troubleshooting Guide

One LED of the central capacity display (1)
flashes.
At least one battery pack is empty.
- Charge the battery packs .
All LEDs of the central capacity display (1)
flash.
Overload: The grass is too high or the cutting height
is set too low.
- Adjust cutting height.
- Let machine cool down until the LED no longer
flash.
The handle is not in position
The knobs (9) are not properly engaged.
- Adjust the height of the handle and make sure that
the knobs (9) and screws (6) are properly aligned.
The machine does not start.
The battery pack performance is weak.
- Charge the battery packs .
The on/off switch (2) is defective.
- Have the on/off switch replaced.
The safety key (16) is not inserted.
- Insert the safety key.
The blade jams.
- Observe the warnings, see chapter 8. Cleaning.
The machine does not mulch properly.
The cutting height is set too low.
- Adjust cutting height.
Wet grass clippings stick to the mower unit.
- Wait until the grass has dried before mowing.
The mulching key (10) is missing.
- Insert the mulching key.
It is difficult to push the machine.
The grass is too high or the cutting height is set too
low.
- Increase cutting height.
The machine vibrates heavily.
The blade is not balanced or worn.
- Replace the blade.
The motor shaft is bent.
1. Switch off the motor.
2. Pull out safety key (16) and remove the battery
packs (18) .
3. Check for damage.
4. Have the machine repaired before putting the
machine back into operation.
The machine stops during the mowing
process.
The cutting height is too low.
- Increase cutting height.
The battery packs are empty.
- Charge the battery packs .
Wet grass clippings stick to the mower unit or blade.
- Remove the battery packs (18) and check the
mower unit.
The operating temperature of the machine is too
high.
18
- Let the machine cool down.
Cuttings do not enter the collection bag.
- Empty the collection bag.

11. Accessories

Use only original Metabo or CAS (Cordless Alliance
System) battery packs and accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
A Blade (sickle blade / as replacement):
Order no.: 628435000
B Battery packs with different capacities. Buy
battery packs only with voltage suitable for your
power tool.
Order no.: 625367000
Order no.: 625368000
Order no.: 625369000
etc.
Order no.: 625591000
Order no.: 625592000
etc.
C Chargers: ASC 55, ASC 145, ASC 145 Duo, etc.
For a complete range of accessories, see
www.metabo.com or the catalogue.
12. Repairs
Repairs to electrical tools must only be carried
out by qualified electricians and only with
original spare parts!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.

13. Environmental Protection

Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Battery packs may not be disposed of with regular
waste. Return faulty or used battery packs to your
Metabo dealer!
Do not allow battery packs to come into contact with
water!
Only for EU countries: never dispose of
power tools in your household waste!
According to European Directive 2012/19/EU
on Waste from Electric and Electronic Equipment
and implementation in national law, used power
tools must be collected separately and recycled in
an environmentally-friendly manner.
Discharge the battery pack in the power tool before
disposal. Prevent the contacts from short-circuiting
(e.g. by protecting them with adhesive tape).
4.0 Ah (LiHD)
5.5 Ah (LiHD)
8.0 Ah (LiHD)
4.0 Ah (Li-Ion)
5.2 Ah (Li-Ion)