Warranty - stayer P910 Bedienungsanleitung

gb
2- If necessary, loosen the clamping element 11
by giving it a light blow with a suitable tool (e.g. a
wooden wedge).
3- Push the planer blade 13 sidewards out of the
blade drum 10 with a piece of wood. Replacing the
Drive Belt (figure H–I) Unscrew screw 6 and take off
the belt cover 7. Remove the worn drive belt 26.
Before assembling a new drive belt 26, clean both
pulleys 27 and 28.
Place the new drive belt 26 on the small pulley 28 first
and then work the drive belt 26 onto the large pulley
27 by hand while rotating it.
Make sure that the drive belt 26 runs exactly in
the longitudinal grooves of the pulleys 27 and 28.
Reattach the belt cover 7 and tighten with the screw 6.
4_MAINTENANCE AND SERVICE
INSTRUCTIONS
Before any work on the machine itself, pull the mains plug.
For safe and proper working, always keep the
machine and ventilation slots clean.
CLEANING
When the carbon brushes wear below acceptable
service tolerances, the machine will automatically cut
out. The machine must be sent to customer service for
maintenance (for address, see the "After-sales Service
and Customer Assistance" section.
If the machine should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for
STAYER power tools.
REPAIR SERVICE
Our after-sales service responds to your questions
concerning maintenance and repair of your product as
well as spare parts. Exploded views and information
on spare parts can also be found under:
info@grupostayer.com
Our customer consultants answer your questions
concerning best buy, application and adjustment of
products and accessories.

WARRANTY

Warranty card
Included in the documentation that accompanies
this equipment, you should find the warranty card.
You should fill out the card completely and return to
vendor with a copy of purchasing receipt or invoice
and you should receive a receipt.
Note: If you cannot find the warranty card within
the documentation, you must ask for it through your
supplier.
The warranty is limited only to manufacturing
defects and expire if pieces have been removed or
manipulated or repaired other than the manufacturer.
DISPOSAL AND RECYCLING
The machine, accessories and packaging should be
sorted for environmental-friendly recycling.
Only for EC countries:
Do not dispose of power tools into
household waste! According the European
Guideline 2002/96/EC for Waste Electrical
and Electronic Equipment and its
implementation into national right, power
tools that are no longer usable must be collected
separately and disposed of in an environmentally
correct manner.
Subject to change without notice.
5_REGULATIONS
TECHNICAL DATA
P = Rated power input
1
R = Load speed
1
Pmax = Maximum depth
Pr = Depth of recess
Ac = Working width, max
= Weight
kg
= Protection class
L = Sound power level
wa
L = Sound pressure level
PA
= Vibration
The values given are valid for nominal voltages
[U] 230/240 V ~ 50/60 Hz. For lower voltage and
models for specific countries, these values can vary.
Please observe the article number on the type plate
of your machine. The trade names of the individual
machines may vary.
EU DECLARATION OF CONFORMITY
The undersigned::
STAYER IBERICA, S.A.
With address at:
Calle Sierra de Cazorla, 7 Área Empresarial
Andalucía - Sector 1 28320 PINTO (MADRID)
Tel.: +34 902 91 86 81 / Fax: +34 91 691 91 72
CERTIFIES
We declare under our sole responsibility that this
product is in conformity with the following standards
or standardized documents: EN 55014-1:2017,
55014-2:2015, EN 6100-3-2:2014, EN 6100-3-
3:2013, EN 62841-1:2015, EN 62841-2-14:2015
according to EU Regulations 2006/42/EC, 2014/30/
EU, 2000/14/EC.
/ /
16
Ramiro de la Fuente
Director Manager
January 2021