Placement And Testing; Changing The Tool - stayer P910 Bedienungsanleitung

4 Lock-off button for On/Off switch
5 On/Off switch
6 Screw for belt cover
7 Belt cover
8 Planer base plate
9 V-grooves
10 Blade drum
11 Clamping element for blade
12 Fastening screw for planer blade
13 Carbide blade
14 Allen key (not included)
15 Handle
16 Chip/dust bag
17 Alternatively output chip
18 Parallel guide
19 Scale for rebating width
20 Locking nut for adjustment of rebating width
21 Fastening bolt for parallel and beveling guide
22 Mains electric
23 Technical data (labels)
24 Fastening bolt for rebating depth stop
25 Rebating depth stop
26 Drive belt
27 Large pulley
28 Small pulley
3_OPERATING INSTRUCTIONS

PLACEMENT AND TESTING

Switching On and Off
To start the machine, first push the lock-off button for
the On/Off switch 4 and then press the On/Off switch
5 and keep it pressed.
To switch off the machine, release the On/Off switch 5.
For safety reasons, the On/Off switch 5 cannot
be locked; it must remain pressed during the
entire operation.
ADJUSTMENT OPERATION
Adjusting the Planing Depth
With the adjustment knob 2, the planing depth can
be adjusted variably from 0–3 mm using the planing
depth scale 1
Planing (Figure D)
Set the required planing depth and place the front part
of the planer base plate 8 against the workpiece.
Apply the machine to the workpiece only
when switched on. Otherwise there is danger
of kickback when the cutting tool jams in the
workpiece.
Switch the machine on and guide the machine with
even feed over the surface to be planed. To achieve
high-grade surfaces, work only with low feed and
apply pressure on the centre of the planer base plate.
When machining hard materials (e.g. hardwood) as
well as when utilising the maximum planer width, set
only low planing depths and reduce planer feed, as
required.
Excessive feed reduces the surface quality and can
lead to rapid clogging of the chip ejector.
Only sharp blades achieve good cutting capacity and
give the machine longer life.
– Switch on the machine.
– Apply the supporting pressure onto the front part of
the planer base plate and slowly push the machine
forward).
This tilts the park rest upward so that the rear part of
the planer base plate faces on the workpiece again.
– Guide the machine over the surface to be planed
with even feed.
Beveling Edges (Figure E):
The V-grooves (9) in the front planer base plate
allow quick and easy beveling of workpiece edges.
Depending on required bevel width, use the
corresponding V-groove. For this, place the planer
with the V-groove onto the edge of the workpiece and
guide it along the edge.
SLOT USED
None
Small
Medium
Large
Planing with Parallel (Figure F-G).
Mount the parallel guide 18 to the machine using the
corresponding fastening bolt 21. Depending on the
application, mount the rebating depth stop 25 with
fastening bolt 24 to the machine.
Loosen the locking nut 20 and adjust the requested
rebating width on the scale 19. Tighten the locking nut
20 again.
Adjust the requested rebating depth accordingly with
the rebating depth stop 25.
Carry out the planing procedure several times until the
requested rebating depth is reached. Guide the planer
applying sideward supporting pressure.

CHANGING THE TOOL

Be cautious when replacing the planer
blades. Do not grasp the planer blades by
the cutting edges. Possible danger of injury
due to the sharp cutting edges of the planer
blades.
The carbide blade has 2 cutting edges and can be
reversed. When both cutting edges are dull, the planer
blade 13 must be replaced. The carbide blade may
not be resharpened.
Disassembling the Planer Blade(s) (Figure A).
To reverse or replace the planer blade 13, rotate the
blade
drum 10 until it is parallel to the planer base plate 8.
1- Loosen the two fastening screws 12 with the Allen
key 14 by approx. 1 – 2 turns.
/ /
15
es
it
gb
de
fr
p
pl
cz
MEASURE A (mm)
0-4
2-6
4-9
6-10