Operation Requirements; Operation; Control - Laserworld ES-50 G Bedienungsanleitung

Manual / Bedienungsanleitung: ES-50 G, ES-100 G

Operation requirements

The operator has to make sure that laser radiation – also reflected laser radiation – higher than
the maximum permissible level is avoided by technical or organisational measures
Make sure to use the correct voltage. Always use a grounded mains connection. Don't use a
remote controlled or other electronically switched main connection. Don't use together with large
appliances (especially fog machines/hazers) on the same mains.
If the device is used in a flying installation, the mounting brackets and an appropriate safety-rope
must be fixed.
In some countries, the operator must notify the accidence insurance and the authority for
industrial safety, before operating a laser. For more information, contact the relevant authorities.
Please consider that unauthorized modifications on the device are strictly forbidden due to safety
reasons!
If this device will be operated in any way differently than described in this manual, the product
may suffer damages and the guarantee becomes void. Furthermore, any other operation may
lead to dangers like short-circuit, burns, electric shock, etc.
Keep surrounding dry and clean.
dusty environment, don't place liquid filled receptacles on the device. Projector should be put in a
water-proof housing when operated outside.
Regularly open the device (see "cleaning" further down) to check for dust inside, or if fog fluid
condenses in the housing (if so rearrange hazer and/or laser position).
Operating temperature is 10~35°C. In a new installation, check after some 15-30 minutes
whether the outlet air gets too warm. Regularly check the inside for dust deposits, especially
around the fans. Let laser cool off 10 minutes after 2 hours of operation, to ensure maximum
lifetime for the diode. Be careful not to direct stage lights toward the laser (especially moving
heads), this can cause overheating.
Distance between laser aperture and projection screen should be not less than 1 meter.
Do not turn device on and immediately off again frequently.
Do not look into the laser beam directly, especially not with optical instruments.
Do not touch the device with wet hands.
When the laser diode becomes dim or broken, please contact your dealer timely.
When returning laser to dealer/manufacturer always use original packaging.
Maintenance should be performed every 15-day period. See "cleaning" further down.

Operation

Caution – use of controls or adjustments or performance of procedures other
than those specified herein may result in hazardous radiation exposure.
Connect the power cable to mains. Connect an emergency switch to the interlock connector, open
shutter, and turn key to on position. The red LED on the front panel should turn on, and the laser
beam will exit through the front opening – be careful.

Control

Setting Switch 10 to „off" puts the device into DMX mode. Connect a DMX controller to operate
the laser. The following operating modes can be selected from the DIP switch on the backside of
the device:
Dip switch
1,0,0,0,0,0,0,0,1,0
0,1,0,0,0,0,0,0,1,0
"Music activ": patterns are changed/animated to the beat of the music. Sensitivity can be adjusted at the back panel.
"Automatic mode": patterns are changed automatically
"DMX": DMX512 Mode. Use the first 9 switches to select the address:
x x x
1 2 4
e.g. 1000 0000 01, DMX mode address 1 (1+0+0+0+0+0+0+0+0+0)
0010 0100 01, DMX mode address 36 (0+0+4+0+0+32+0+0+0)
This unit should be keep dry, do not use in the rain or damp and
Mode
Music active, beam effects
Music active, graphics
x x x
8 16 32
1,0,0,0,0,0,0,0,0,0
0,1,0,0,0,0,0,0,0,0
x,x,x,x,x,x,x,x,x,1
x x x
64 128 256
Page / Seite 4 of / von 10
Automatic, beam effects
Automatic, graphics
DMX
Version / Stand: June 13