Functional Description - Maktec MT450T Bedienungsanleitung

FUNCTIONAL DESCRIPTION

CAUTION:
Always be sure that the tool is switched off and
•
unplugged before adjusting or checking function
on the tool.
Adjusting the shoe
Fig.1
Fig.2
When the blade loses its cutting efficiency in one place
along its cutting edge, reposition the shoe to utilize a
sharp, unused portion of its cutting edge. This will help
to lengthen the life of the blade. To reposition the shoe,
push the shoe button in the "A" direction with a click and
reposition as shown in the figure which allows you to
make five-way adjustment. To secure the shoe, push
the shoe button in the "B" direction with a click.
Switch action
CAUTION:
Before plugging in the tool, always check to see
•
that the switch trigger actuates properly and
returns to the "OFF" position when released.
Switch can be locked in "ON" position for ease of
•
operator comfort during extended use. Apply
caution when locking tool in "ON" position and
maintain firm grasp on tool.
Fig.3
To start the tool, simply pull the switch trigger. Tool
speed is increased by increasing pressure on the switch
trigger. Release the switch trigger to stop.
For continuous operation, pull the switch trigger, push in
the lock button and then release the switch trigger.
To stop the tool from the locked position, pull the switch
trigger fully, then release it.
ASSEMBLY
CAUTION:
Always be sure that the tool is switched off and
•
unplugged before carrying out any work on the
tool.
Installing or removing the saw blade for
Model MT450T
CAUTION:
Always clean out all chips or foreign matter
•
adhering to the blade, blade clamp and/or slider.
Failure to do so may cause insufficient tightening
of the blade, resulting in a serious injury.
Fig.4
To install the saw blade, always make sure that the
blade clamp lever is in released position
insulation cover before inserting the saw blade. If the
Downloaded from www.Manualslib.com manuals search engine
blade clamp lever is in fixed position, rotate the blade
clamp lever in the direction of the arrow so that it can be
locked at the released position .
CAUTION:
If you do not insert the saw blade deep enough,
•
the saw blade may be ejected unexpectedly during
operation. This can be extremely dangerous.
Keep hands and fingers away from the lever
•
during the switching operation. Failure to do so
may cause personal injuries.
Fig.5
Insert the saw blade into the blade clamp as far as it will
go. The blade clamp lever rotates and the saw blade is
fixed. Make sure that the saw blade cannot be extracted
even though you try to pull it out.
Fig.6
To remove the saw blade, rotate the blade clamp lever
in the direction of the arrow fully. The saw blade is
removed and the blade clamp lever is fixed at the
released position .
NOTE:
If you remove the saw blade without rotating the
•
blade clamp lever fully, the lever may not be
locked in the released position
rotate the blade clamp lever fully again, then make
sure that the blade clamp lever locked at the
released position .
If the lever is positioned inside the tool, switch on
•
the tool just a second to let the blade clamp out.
Switch off and unplug the tool from the mains
before working on the blade clamp lever.
Installing or removing the saw blade for
Model MT450
CAUTION:
Always clean out all chips or foreign matter
•
adhering to the blade, blade clamp and/or slider.
Failure to do so may cause insufficient tightening
of the blade, resulting in a serious injury.
Fig.7
To install the blade, loosen the screw on the blade
clamp with the hex wrench. Insert the blade between
the blade clamp and the slider so that the pin on the
slider fits into the hole in the blade shank. If the pin
cannot easily fit into the hole, remove the hex wrench
from the screw and then try again.
CAUTION:
If you tighten the screw without the pin on the
•
slider fitting properly in the hole in the blade shank,
the pin or the blade shank will be damaged. This
may cause the blade to be extracted unexpectedly
on the during operation.
5
. In this case,