Renkforce 1404054 Bedienungsanleitung Seite 2

G Operating instructions
IDE Adapter
Item no. 1404054
Intended use
The product is intended to run an IDE hard drive of type 6.35 cm (2.5") connected via a
standard 40- or 80-pin IDE cable (used for 8.89 cm/3.5" IDE hard drives).
Always observe the safety instructions and all other information included in these op-
erating instructions.
This product complies with the applicable national and European requirements. All
names of companies and products are the trademarks of the respective owners. All
rights reserved.
Package contents
• IDE adapter
• Operating instructions
Latest operating instructions:
1. Open produktinfo.conrad.com in a browser or scan
the displayed QR code.
2. Select document type and language and enter the
item number into the search field. After submitting
the query you can download displayed records.
Explanation of symbols
This symbol indicates specific risks associated with handling, operation or
use.
The "arrow" symbol indicates special tips and operating information.
Safety instructions
The warranty/guarantee will be void in the event of damage caused by fail-
ure to observe these operating instructions! We do not assume any liability
for any resulting damage!
We do not assume any liability for material and personal damage caused by
improper use or non-compliance with the safety instructions. The warran-
ty/guarantee will be void in such cases.
• Unauthorised conversion and/or modification of the product is not permit-
ted for safety and approval reasons (CE).
• The product is not a toy and does not belong in the hands of children!
• The product is only suited to dry indoor locations and must not get damp
or wet.
• Ensure that the cables do not get kinked or pinched.
• Do not leave the packaging materials unattended. They may become dan-
gerous playthings for children.
• Should any questions arise that are not answered in these operating in-
structions, please contact us or another specialist.
Connection
6.35 cm/2.5" IDE hard drive
Power connector
40-pin or 80-pin
IDE cable
The IDE adapter contains no electronics assembly and simply converts dif-
ferently shaped connectors and facilitates the voltage/current supply to the
small 6.35 cm/2.5" hard disk (5 V/DC via PC adapter).
• Turn off the computer in which you intend to install the product and unplug it from
the mains voltage. Disconnect the mains plug from the mains socket. Only now
should you open the computer.
• Attach the 40-pin or 80-pin IDE cable to the IDE adapter. Pay attention to the correct
orientation (pin 1 on the IDE cable is marked in colour. See pin 1 on the IDE adapter
in the picture above).
• Connect the IDE adapter to your 6.35 cm/2.5" IDE hard drive (the single missing pin
on the hard drive 44-pin connector is normal). Also here check that the IDE adapter
is properly plugged in, see image above.
• If two IDE hard drives are connected to one IDE cable, one has to be set as "Master"
and the other as "Slave". Otherwise, the two hard drives may not function properly
or not at all.
A small jumper is used for the "Slave" on a 6.35 cm/2.5" IDE hard drive. See
image above. However, do not use a standard 2.54 mm pitch jumper shunt
(as you would for 8.89 cm/3.5" hard drives), but a little jumper in 2 mm pitch.
Search the internet for the related operating instructions or the manufac-
turer's information to know how to change the configuration on 8.89 cm/3.5"
IDE hard drives (or optical drives).
• Finally plug the power of the IDE adapter into the appropriate connector of your PC
power supply.
If the power connection is not plugged into the computer's power supply the
6.35 cm/2.5" hard drive will not work.
• Secure the 6.35 cm/2.5" IDE hard drive with screws at a suitable place in your com-
puter. Make sure that the screws used are not so long that they could damage the
hard drive.
• Route the cables so that they cannot get caught in the computer fan. Use cable
fasteners to fix the cables in place.
• Close the computer case again. Reconnect the PC to the mains voltage and switch
it on.
It may become necessary to change the setting in the BIOS/setup, so that
the hard drive is recognized.
Disposal
The product must not be disposed of in household waste!
Please dispose of the product at the end of its service life according to the
current statutory requirements.
Technical data
Power supply ...................................... via PC power supply
Suitable for ......................................... 6.35 cm/2.5" IDE hard drive
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent
the technical status at the time of printing.
© Copyright 2015 by Conrad Electronic SE.
Pin 1
Master
Slave
IDE Adapter
Pin 1
Pin 1