Kity 706 Originalanleitung Seite 18

Adjustment of oblique cut Fig. A8
Loosen clamping lever (P), adjust the desired
degree count with the lateral handwheel (R) on
the scale (S), and tighten the clamping lever
again.
ON and OFF switch Fig. A8
Each activation of the switch allows the start of
its own function - setting the master switch (T) to
the sawing mode (see icons on switch box)
Green button Activate
Red button Deactivate
In case of danger, lateral Emergency-Stop
switch
Caution: To start a function, one must unlock
the stop switch without fail.
Working on the circular table saw
Use only fault-free and well sharpened saw
blades. Check to ensure that the splitting wedge
and protective hood have stable bases. Adjust
the protective hood according to the workpiece
thickness
Move the workpiece with both hands, use slide
rod without fail in the area of the saw blade and
push the workpiece up to the rear of the splitting
wedge
Lock long workpieces to prevent tilting over at
the end of the cutting operation.
Installation and operation of the milling
machine
2.0 Milling machine (B)
A Milling machine protection
B Stop bar
C Guide bar
D Press protection
E Height adjustment with scale
F Spindle clamping
D GB
G Carriage
H Cross sectional stop with clamping unit
I Small delivery table
K Vacuum suction nozzle
L Tommy screws
M Machine table
Caution: Disconnect the power plug before
performing adjustment and retrofitting jobs.
Installation of milling machine guard Fig.
B 1
Take saw blade to the lowest position.
Remove the table insertion rings.
Position the milling machine guard (A) on the
Cross table with telescopic arm ..............................................................................Art. Nr. 1902103701
Pin cutting device ......................................................................................................Art. Nr. 1902403702
machine table (M) and install in the existing
threaded holes with 2 tommy screws (L). Ensure
that the milling machine guard is aligned parallel
to the table.
Installation of the tool Fig. B 2 and B 3
Loosen the clamping screw (P) on the milling
machine guard (A) and push it inwards, detach
the tommy screw (N) and tilt the press protection
(D) upwards. Tighten the tommy screws again to
prevent toppling. (Fig. 2)
Open the spindle screw (N) with the Allen
wrench and resist it with the open-end wrench
(Fig. 3)
Place the tool on the spindle, keeping the
distance between the tool and the bearing shell
as small as possible, and pay attention to the
direction of rotation of the tool.
To mount the tool effectively, the top-most ring
with the pin must be inserted into the groove of
the spindle. It must protrude from the spindle
shaft by at least 5 mm.
Tighten the tool with the spindle screw and the
Allen wrench, and resist it with the open-end
wrench (Fig. 3)
Important: When the tools are lowered,
keep the passage opening between the tool
and the table insertion rings as narrow as
possible.
Height adjustment of the spindle Fig. B 4
Loosen clamping screw (F),
Adjust the milling spindle with the hand wheel
(E)
Tighten clamping screw (F) again
Note: After setting the milling spindle always
clamp it to avoid vibrations and displace-
ment of the spindle.
Adjusting speed Fig. B 5 and B 6
Loosen the knurled screw (1) on the viewing
doors (2) and open the doors
Loosen the permanently clamping lever (3) and
release the V-belt
Move the V-belt (4) according to rotary speed
(depending on material and tool)
Stretch V-belt, tighten tommy screw
Shut the doors, turn the knurled screw up to the
end (for safety)
Working with the milling machine
Correct setting up of machine saves time and
is the precondition for safe jobs.
Accessories
18
Selection of tool ( feed type, material of workpi-
ece)
Checking tool (status of cutting and contact
surfaces)
Install tool in the correct direction of rotation
Cutting height and depth to be installed only
when machine not in operation
Bring protective device and set the operation
accordingly
Tighten all connections for safe working
Always perform sample milling with the protecti-
ve device on
Perform milling only with rebound protection
Always wear ear protection during stay
ON and OFF switch Fig. A 8
Each ON switch allows the start of its own
function
Set master switch (T) in the milling mode (see
icons on the switch box)
Green button - Activate
Red button - Deactivate
In case of danger, press lateral Emergency-Stop
switch
Caution: To start a function, one must un-
lock the stop switch without fail.
Slide carriage Fig. B 7
The slide carriage is fully installed.
To unlock, pull out the button (5) laterally on the
table, rotate ¼ turn to the right and re-engage.
Delivery table Fig. B 8
Install table (6) if necessary, laterally with 2
tommy screws.
Slide carriage with clamping device and
angle setting Fig. 8
Introduce angle stop (7) into the groove of the
slide table with the guide bar and tighten with
the turning handle (9).
For angle settings, loosen the tommy screws
(10), set angle and tighten again.
Place the tool clamp (11) in the opened state
over the workpiece, tighten the clamping screw
(12) and clamp the workpiece with the eccentric
lever (13).