Kity 706 Originalanleitung Seite 17

ece guides and moving machine parts.
Injuries due to flying tool components after a
tool suffers breakage.
Injuries (suffered) due to
flying workpiece parts.
Risk of fire from flames or heat radiation. Risk
when working on the electrical system. Inhalati-
on of dust or poisonous vapours.
Transport protection: Wood lining
Delivery: Machine mounted on wood pallet
Caution: Collision or heavier loads must be
avoided, these can lead to damages to the
machine and to disturbances in the settings.
Unpack the machine preferably in the room in
which it will be operated
Deposit the machine with a crane at the provi-
ded place
Tie ropes only at the specified positions
Caution: Do not lift the machine by the
tables
Attention: Before operation, be sure to fix the
machine on level concrete ground and start the
dust exhaust system first.
The resistance of the hoses fixed shall be less
than 1000000 ohm
Installation of the slide table
Unpack the slide table and put it
on a table/workbench.
Remove the two nuts from the screws mounted
on the bottom side of the slide table, and keep
them at a safe place. (will be required for subse-
quent installation)
Fig. E1
Take the table out and remove the plastic flap (1)
(do this on
both sides)
Fig. E2, E3
The stops (2, 3) for the slide table are already
set at the factory
Just place the table on the frame of the machine
(ideally with 2 persons).
Pull the Allen screw (4) softly with the help of the
wrench (on both sides), move the table towards
the Stop screws (2). You may now tighten the
Allen screws (4).
Fig. E4
Now screw the nuts that you removed from the
table at the start on the bolt of the table and tigh-
ten them uniformly
As final control, place a straight rod on the slide
table, and check the surface of the machine
table. Ideally, the slide table is a couple of one-
tenth millimetres higher than the machine table
Installation and operation of the saw
1.0 Circular saw (A)
A Saw blade
B Splitting wedge
C Protective hood
D Longitudinal stop
E Guide bar of longitudinal stop
F Height adjustment of saw blade
G Oblique cutting adjustment
H Switchbox
Transport
Unpacking
Disposal of packaging material
The packing protects the machine from trans-
port damages.
The packaging material can be recycled, and
can be reused in the waste management cycle.
Packaging components such as films, plastic
and plastic bags can be dangerous for children.
Installation / Operation
For technical packaging reasons, your machine
is not fully assembled.
•
Open the box and remove the package
components
•
Take out the attached individual parts.
Caution: Disconnect the power plug before
performing adjustment and mounting jobs
Installation of splitting wedge and protective
hood Fig. A1 and A2
Unlock the carriage (A) and pull it back to
the stop, slide back the safety guard (B)
•
Turn the wheel for the height adjustment to
the highest position of the saw blade.
•
Detach the screw on the terminal block (C)
and insert the splitting wedge (D) between
the metal plate and the terminal block
•
Adjust the height of the splitting wedge
such that the gap between the splitting
wedge and saw teeth along the curve of the
saw blade is exactly the same and is not
more than 5 mm.
•
Tighten the screw to keep the splitting
wedge at its place and position.
Mounting and removal of the saw blade
guard, Fig. A3
•
Loosen the tommy screw (F) to remove
the protective device (E), then pull out the
guard.
•
To re-install the protective device, put it on
the splitting wedge such that the screw fits
into the slot of the splitting wedge.
•
Push the protective device such that the
screw fits into the recess of the slot.
•
Tighten the tommy screw adequately, so
that the protective device rests on the table
plate, but raises itself if the workpiece is
pushed against the saw blade. Please note:
After cutting the workpiece, the saw blade
guard must return to its resting position.
•
Connect the hose (G) between the outlet of
the protective device and one of the suction
nozzles.
Fastening the suction hose Fig. A 3.1
To keep the saw table free, the support of the
17
There is risk of suffocation.
Keep the packaging components outside the
reach of children and dispose of them as fast as
possible
suction hose is mounted laterally on the frame of
the planing table
Caution: To avoid contact with the saw blade,
the saw blade guard must always be in the wor-
king position. It should lift itself on the workpiece
during the sawing operation.
Saw blade change Fig. A1, A2, A3 and A4
Disconnect the power plug.
Unlock carriage (A) and move it back up to the
stop
Remove the protective hood
Slide back the safety guard (B)
Turn saw blade till the locking pin (H) engages
Detach screw, remove flange and saw blade
Exercise caution as there is risk of physical
injury
Clean the supporting surfaces before the
insertion
Replace the saw blade, (pay attention to the
correct running direction)
Place the flange and tighten the screw
Remove the locking pin
Readjust the splitting wedge if necessary (dis-
tance 3 – 5 mm)
Slide the safety guard on again till the limit
switch engages
Place the protective hood again and tighten it.
Move the carriage back to the starting position
till it engages
Adjustment of the longitudinal stop Fig. A5,
A6, and A7
Introduce the guide rail (I) in the saw table (K)
and fasten it with 2 tommy screws (L)
Insert the longitudinal stop (M) with the guide
carriage and exact setting into the guide rail and
clamp tightly. Position the stop on the saw blade
and fix on "0".
The stop (N) can be installed at the left or right
of the saw blade.
Comment: To ensure an exact cut, check the
parallel position of the longitudinal stop and
readjust if necessary.
Height adjustment of cut Fig. A8
Loosen clamping screw (U), adjust the cutting
height with the handwheel (O), and tighten the
clamping screw again.
D GB