Important Safety Instructions - Hamilton Beach Summit Serie Bedienungsanleitung

Blender Safety
IMPORTANT: This operation manual should be reviewed with all equipment operators as part of your
operator training program.
WARNING –
the following:
• Read the Operation Manual before using blender.
Keep Operation Manual handy.
• Before first use, wash container assembly in hot, soapy
water. Do NOT place in dishwasher.
• Plug into a grounded outlet.
• Do not remove ground.
• Do not use an adapter.
• Do not use an extension cord.
• Disconnect power before cleaning or servicing.
• To reduce risk of personal injury, unplug cord from outlet
when not in use, and before putting on or taking off parts.
• Unplug the blender and inspect the power cord insulation
for cracks on a weekly basis. Refer to "Technical Services"
for repair or replacement.
• To protect against electrical shock, do not immerse cord,
plug, or blender base in water or any other liquid.
• Do not spray the base with a high-pressure spray gun.
• Extreme caution must be used when moving an
appliance containing hot oil or other hot liquids.
• Do not use appliance for other than intended use.
• Not intended for use by or near children.
• Children should be supervised to ensure they do not play
with the appliance.
• This appliance is not intended for use by persons
(including children) with reduced physical, sensory, or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
• The use of accessory attachments not recommended
by the appliance manufacturer may cause injuries.
• To reduce risk of personal injury and to prevent damage to
blender or container and cutter assembly, DO NOT insert
utensils into blender container while operating blender.
• Do not store any kitchen utensils in the container because
the blender would be damaged if inadvertently turned on.
• To prevent possibility of serious personal injury, keep hands
out of blender container while operating blender. Always
operate blender with container cover in place.
• Avoid contacting moving parts. Switch off the appliance and
disconnect from power supply before changing accessories
or approaching parts that move in use.
• Blades are sharp. Handle carefully when emptying
container and during cleaning and inspecting of blades.
• If cutter assembly blades are loose, discontinue use
immediately and replace cutter assembly. Do not attempt
to repair or tighten cutter assembly.
• Inspect container and cutter assembly daily. Do not use
broken, chipped, or cracked container. Check cutter for
wear, nicks, or broken blades. Do not use broken, loose,
or cracked cutting blades.
• Do not use outdoors.
• This appliance is intended for short periods of operation,
with a rated operating time of 3 minutes.
• Do not leave blender unattended while it is operating.
• To prevent damage to blender, container, or cutter
assembly, DO NOT move or shake blender while in
2
Downloaded from www.Manualslib.com

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, basic safety precautions should be followed, including
SAVE THESE INSTRUCTIONS
–
manuals search engine
operation. If blending action stops during operation,
turn blender OFF (O), remove container from base,
remove container cover, and use a thin rubber spatula
to push mixture towards cutters.
• When blending hot liquids, remove center piece of
two-piece lid. Hot liquids may push lid off jar during
blending. To prevent possible burns: Do not fill blender jar
beyond the 1 quart (1 liter) level. With the protection of an
oven mitt or thick towel, place one hand on top of lid. Keep
exposed skin away from lid. Start blending at lowest speed.
• Always operate blender with container cover in place.
• Do not defeat the jar pad sensors.
• Do not drop or slam the Quiet Shield
• Keep fingers away from edges and joints when opening and
closing the Quiet Shield ™ .
• Always use the handle to open and close the Quiet Shield
• Do not strike the container against a surface to loosen
ingredients.
• Do not carry the unit by the power cord.
• Do not immerse in liquids or wash the blender base
in a dishwasher.
• Do not place blender base in or near liquids.
• Only authorized service facilities should repair the blender.
• Do not operate the above-the-counter model without the
lower housing securely in place.
• This product is not intended to be installed in an
unventilated cabinet. Ensure that there is a minimum of
7.75 in 2 (5000 mm 2 ) of ventilation below the cabinet when
operating in the in-counter configuration.
• This blender is designed with motor overload protection.
If the motor stops during operation due to overheating,
unplug the unit and allow it to cool down for 15 minutes.
Plug unit back in after 15 minutes to resume normal
operation.
• The normal function of this product may be disturbed by
strong electromagnetic interference. If this occurs, simply
reset the product and resume normal operation by following
the operation manual. If normal operation cannot be
resumed, place the product in a different location.
• The USB port on this product is not intended to be
connected to a PC or any other electronic device. Use it
only to upload programs provided by the manufacturer
on a USB flash drive.
• Do not operate any appliance with a damaged cord or plug
or after the appliance malfunctions, or is dropped or
damaged in any manner. Refer to "Technical Services" for
instructions on examination, repair, or electrical or
mechanical adjustment.
• If the supply cord of this appliance is damaged, it must be
replaced by the manufacturer or its service agent or a
similar qualified person.
UK ONLY: If fitted with a non-rewirable U.K. plug, the 13-
amp fuse approved by ASTA to be B.S. 1362 must be used.
If you need a replacement fuse carrier, it must be replaced
with the same colour-coded carrier with the same markings.
Fuse covers and carriers can be obtained from approved
service agents.
™ .
™ .
–