Starting And Stopping; Removing Blockage - Bosch AXT Rapid 2000 Bedienungsanleitung

F 016 L70 461 - GB Seite 3 Freitag, 7. Juli 2006 1:40 13
Products sold in GB only: Your machine is fitted with
an approved 13 A (BS 1363/A) electric plug and is
protected by a 13 A fuse (ASTA Approved to
BS 1362).
If the fitted plug is not suitable for your socket out-
lets, it should be cut off and an appropriate plug fitted
in its place.
The severed plug must be disposed of to avoid a
possible shock hazard and should never be inserted
into a 13 A socket elsewhere.
Assembly
Remove the machine from the package.
A
Mount the wheels and the undercarriage.
B
Fit the Allen key 12 as shown.
E

Starting and Stopping

C
Starting:
To start your Shredder, rotate the On/Off switch 2
from position "0" to position "II". Allow machine to
start and release switch, which will return to position
"I" (the normal run position).
Important note: The machine will not start if the
On/Off switch 2 is pushed in slightly, whilst be-
ing rotated.
As a safety feature the machine will not start unless
the hopper securing knob 3 is fully tightened.
Stopping:
Rotate the On/Off switch 2 to position "0".
Note: The blade will stop automatically before the
cover 11 can be removed.
Emergency Stop:
Press the On/Off switch 2.
Restart Protection
After a mains failure, or if the product cuts out due to
overloads, the machine cannot restart on its own
when the power returns or when protector resets.
To restart the machine:
Set the On/Off switch 2 to "0".
14 • F 016 L70 461 • TMS • 07.07.06
Downloaded from www.Manualslib.com
The blade continues to rotate for a few
seconds after the machine is switched off.
Allow the motor/blade to stop rotating be-
fore switching "on" again.
Do not rapidly switch off and on.
manuals search engine
Rotate the On/Off switch 2 to position "II", al-
low the machine to start and release the
switch. It will now move to position "I" (the nor-
mal run position).
Important note: The machine will not start if the
On/Off switch 2 is pushed in slightly, whilst be-
ing rotated.
Overload Protection
Overloading (e. g. blocking up of the cutter) can lead
to a standstill of the machine after a few seconds. Af-
ter a short period, the machine can be switched on
again. If the machine blocks again turn it off.
Remove blockage (see "Removing blockage"), and
restart.
Shredding
In order to collect the chopped material, fasten the
carrying straps of the collecting bag 7 (accessory) to
the two hooks 9 while the shredder is switched off.
Feed the material to be chopped through the feed in-
take.
Longer material standing out from the ma-
chine could lash out when being cut! Small
pieces of shredded material may be
ejected from the feed intake. Ensure eye
protection, protective gloves and ear pro-
tection are used when using the machine.
Only insert as much material so that the feed in-
take 1 will not be blocked up.
Do not fill soft waste such as kitchen rubbish into the
shredder but compost directly.
Take care that the chopped material can fall freely
from the discharge chute 8 – danger of backing up!
The ventilation slots 5 must not be covered by the
collecting bag or the chopped material.
Avoid blocking the discharge chute 8 with shredded
material as this could result in kickback of material
through the feed intake opening.

Removing Blockage

Stop and remove plug from the power sup-
ply.
After fully unscrewing the securing knob 3, remove
cover 11 and clean the blade area. If debris is com-
pacted in the blade area, remove with a wooden or
plastic implement. Also clean the discharge chute 8
of any debris.
English - 3