Using The Saw - EINHELL NEW GENERATION NTS 1525 Originalbetriebsanleitung

Anleitung_NTS_1525_SPK7:Anleitung TKS 15-250 UV SPK 1
used on the sides.
Now mount the rubber feet (43) on the legs and
turn the saw together with the base frame so
that it stands upright on the floor.
Finally, secure all the screws and nuts on the
base frame so that they are tight (Fig. 18).
Screw the additional legs (A) to the rear legs
(29) so that they point towards the rear of the
machine (Fig. 26).
7.2 Table width extension and length extension
(Fig. 19/20)
Use the screws and nuts to fasten the table
width extension and length extension (35/36)
loosely to the saw table (1) (Fig. 19).
Screw the supports (27) loosely onto the saw
housing and onto the table width extension or
length extension (short supports for the width
extension, long supports for the length
extension).
Align the table width extension and length
extension level with the saw table (1).
Finally, tighten all screws. (Fig. 20)
7.3 Fitting / removing the saw blade guard (Fig. 3)
Mount the saw blade guard (2) on the splitter (5)
so that the screw fits through the hole (44) in the
splitter.
Do not tighten the screw (15) too far – the blade
guard must be able to move freely.
Fasten the extractor hose (13) to the extractor
adapter (16) and to the extractor socket of the
blade guard (2).
A suitable extractor system has to be connected
to the outlet of the extractor adapter (16).
To remove the saw blade guard, proceed in
reverse order.
Important!
The guard hood (2) must always be lowered
over the workpiece before you begin to cut.
7.4. Setting the splitter (Fig. 3/6/7/8)
Important! Pull out the power plug.
Set the blade (4) to max. cutting depth, move to
0° position and lock in place.
Remove the saw blade guard (see 7.3).
Take out the table insert (6) (see 7.5).
Slacken the fixing screw (20).
7.4.1. Setting for maximum cuts (Fig. 6/7/8)
Push up the splitter (5) until the gap between the
saw table (1) and the upper edge of the splitter
(5) equals approx. 10 cm.
The distance between the blade (4) and the
splitter (5) should be 3-5 mm.
Retighten the screw (20) and mount the table
05.10.2010 8:12 Uhr
insert (6) (Fig. 7).
7.5 Changing the table insert (Figure 7)
To prevent increased likelihood of injury the
table insert should be changed whenever it is
worn or damaged.
Remove the saw blade guard (2).
Remove the 2 countersunk head screws (34).
Take out the worn table insert (6).
To fit the replacement table insert, proceed in
reverse order.
7.6 Fitting/replacing the blade (Fig. 5)
Important! Pull out the power plug first.
Remove the table insert by undoing the two
countersunk head screws (see 7.5).
Undo the nut with a size 24 wrench on the nut
itself and a second fork wrench (size 13) on the
motor shaft (a) to apply counter-pressure.
Important! Turn the nut in the direction of
rotation of the saw blade.
Take off the outer flange and pull the old saw
blade off the inner flange by dropping the blade
at an angle.
Clean the blade flange thoroughly before fitting
the new blade.
Mount and fasten the new saw blade in reverse
order.
Important! Note the running direction. The
cutting angle of the teeth must point in
running direction, i.e. forwards (see the
arrow on the blade guard).
Refit and set the splitter (5) and the saw guard
(2) (see 7.3., 7.4.)
Check to make sure that all safety devices are
properly mounted and in good working condition
before you begin working with the saw again.

8. Using the saw

8.1. ON/OFF switch (Fig. 4)
To turn the saw on, press the green button .I. .
Wait for the blade to reach its maximum speed
of rotation before commencing with the cut.
To turn the machine off again, press the red
button "0".
8.2. Cutting depth (Fig. 4)!
Turn the hand crank (8) to set the blade (4) to
the required cutting depth.
Turn anti-clockwise: larger cutting depth
Turn clockwise: smaller cutting depth
Seite 17
GB
17