Technical Data; Before Putting The Machine Into Operation - EINHELL NEW GENERATION NTS 1525 Originalbetriebsanleitung

Anleitung_NTS_1525_SPK7:Anleitung TKS 15-250 UV SPK 1
GB
Please note that our equipment has not been
designed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.

5. Technical data

AC motor
Power P S1 1200 W S6 40% 1500 W
Idle speed n
0
Cutting-off wheel Ø 250 x Ø 30 x Ø 2.4 mm
Number of teeth
Table size
Table width extension, left/right
Table length extension, rear
Cutting height max.
Height adjustment
Tilting saw blade
Extractor socket
Weight
Sound and vibration
Sound and vibration values were measured in
accordance with EN 61029.
Idle
L sound pressure level 93,5 dB
pA
K uncertainty
pA
L sound power level 105,0 dB
WA
K uncertainty
WA
The quoted values are emission values and not
necessarily reliable workplace values. Although there
is a correlation between emission and immission
levels it is impossible to draw any certain conclusions
as to the need for additional precautions. Factors
with a potential influence on the actual immission
level at the workplace include the duration of impact,
the type of room, and other sources of noise etc.,
e.g. the number of machines and other neighboring
operations. Reliable workplace values may also vary
from country to country. With this information the
user should at least be able to make a better
assessment of the dangers and risks involved.
16
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect working
order.
Service and clean the appliance regularly.
Adapt your working style to suit the appliance.
Do not overload the appliance.
230V - 240V 50Hz
Have the appliance serviced whenever
necessary.
Switch the appliance off when it is not in use.
5700 min -1
24
6. Before putting the machine into
610 x 440 mm
operation
610 x 250 mm
440 x 320 mm
Unpack the bench-type circular saw and check it
73 mm / 90° for damage which may have occurred in transit.
The machine has to be set up where it can stand
53 mm / 45°
firmly, e.g. on a work bench, or it must be bolted
infinite 0 -73 mm
to a strong base.
infinite 0° - 45°
All covers and safety devices have to be
Ø 35 mm properly fitted before the machine is switched
on.
27 kg
It must be possible for the saw blade to run
freely.
When working with wood that has been
processed before, watch out for foreign bodies
such as nails or screws etc.
Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the
machineʼs moving parts run smoothly.
Before you connect the machine to the power
mode
supply, make sure the data on the rating plate is
106,7 dB
the same as that for your mains.
3 dB
114,5 dB
7. Assembly
3 dB
Important! Pull out the power plug before
carrying out any maintenance, resetting or
assembly work on the cutting-off machine!
7.1 Assembling the base frame (Fig. 17/18)
Turn the saw upside down and place it on the
floor.
Use the hex screws and nuts to fasten the four
legs (40) loosely to the saw.
Now fasten the longitudinal struts and cross
struts (41) as well as the four center struts (42)
loosely to the legs.
Be sure to secure the hex screws and nuts only
loosely. Important: The longer struts have to be
05.10.2010 8:12 Uhr Seite 16