Operation; Maintenance; Optional Accessories - Makita UT2204 Betriebsanleitung

carbon brushes may be worn out, or the motor or the
switch may be defective. If the indicator lamp does not
light up, the mains cord or the indicator lamp may be
defective. When the mains cord is defective, the tool
neither starts nor lights the indicator lamp. When the
indicator lamp is defective, the tool starts without the
indicator lamp lighting up.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Installing shaft (Fig. 3 & 4)
Tighten the shaft with hex nut into the shaft holder as far
as the hex nut comes into contact with the holder. Hold
the notch in the shaft holder with wrench 19 so that it
cannot revolve. With the notch held so, tighten the hex nut
with another wrench 19 in the direction of arrow.
Installing mixing blades (Fig. 5 & 6)
Insert the mixing blade into the shaft and secure it with the
hex bolt.
At this time, position it so that the top end of the hex bolt
always fits to the flat surface on the shaft and tighten the
hex bolt with the provided wrench.
When installing the mixing blades at two different
positions (which is applicable only to the mixing blades
allowed to do so), mount and secure the two mixing
blades on the flat part of the shaft with the hex bolts so
that the same surface of blades faces each other as
shown in the figure. (Fig. 7 & 8)

OPERATION

Mixing
CAUTION:
• Do not use to mix flammable material such as paint
with thinner used as solvent. Failure to do so may
cause injury.
1. Hold the rear handle of the tool with one hand and the
grip with the other hand firmly, place the mixing blade
under material fully and turn on the tool after making
sure work site safety.
2. Move the mixing blade up and down during the mixing
operation so that whole part of material can be mixed.
3. When finishing mixing, turn off the tool, make sure that
the mixing blade has come to a complete stop, and
then pull it out of the vessel.

MAINTENANCE

CAUTION:
• Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
Replacing filter (Fig. 9)
Replace the filter regularly as the cooling efficiency of the
tool is reduced due to built-up dust or particles in the filter.
Downloaded from www.Manualslib.com manuals search engine
Insert the slotted bit screwdriver and the like between the
tool and the cover as shown in the figure. Lift it up just like
using a shovel and remove the cover.
Replace the filter in the cover with a new one.
Reinstall the cover on the tool.
Replacing carbon brushes (Fig. 10)
Remove and check the carbon brushes regularly. Replace
when they wear down to the limit mark. Keep the carbon
brushes clean and free to slip in the holders. Both carbon
brushes should be replaced at the same time. Use only
identical carbon brushes.
Use a screwdriver to remove the brush holder caps. Take
out the worn carbon brushes, insert the new ones and
secure the brush holder caps. (Fig. 11)
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers, always
using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Mixing blades
• Shaft
NOTE:
• Some items in the list may be included in the tool
package as standard accessories. They may differ
from country to country.
Noise
The typical A-weighted noise level determined according
to EN60745:
Sound pressure level (L
Sound power level (L
WA
Uncertainty (K): 3 dB (A)
Wear ear protection
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745:
Vibration emission (a ): 2.5 m/s
h
Uncertainty (K): 1.5 m/s
• The declared vibration emission value has been
measured in accordance with the standard test method
and may be used for comparing one tool with another.
• The declared vibration emission value may also be
used in a preliminary assessment of exposure.
WARNING:
• The vibration emission during actual use of the power
tool can differ from the declared emission value
depending on the ways in which the tool is used.
• Be sure to identify safety measures to protect the
operator that are based on an estimation of exposure in
the actual conditions of use (taking account of all parts
ENG905-1
): 83 dB (A)
pA
): 94 dB (A)
ENG900-1
2
or less
2
ENG901-1
5