Werbung
Verfügbare Sprachen
Verfügbare Sprachen
O P E R A T I N G I N S T R U C T I O N S
2 port serial Mini-PCIe plug-in card
Item no. 97 61 92
Intended Use
The product is intended to be installed into a computer with a Mini-PCIe slot in order to provide
for two additional RS232 interfaces.
This product complies with the applicable National and European requirements. All names of
companies and products are the trademarks of the respective owner. All rights reserved.
Package Contents
• Plug-in card
• Two connecting cables (mini plug on 9 pol. RS232 connectors)
• Mains cable
• CD with driver
• Operating Instructions
Description
1 9 pole terminal strip for RS232-port #1
2 9 pole terminal strip for RS232-port #2
3 Electrical connection
4 Jumper for switching between 5 V/DC
and 12 V/DC on pin 9 on the 9 pole
SubD-contact.
5 Jumper for switching between,
pin 9 for DC-Bus-Power- or RI func-
tionality
6 Terminal strip for Mini-PCIe-slot.
Installation
If you do not have the expertise to install the device correctly, please contact
an expert or a specialist workshop and let them carry out the installation!
Incorrect installation can cause damage to the plug-in card and also to your
computer and all connected devices.
Caution, lethal hazard!
Switch off all connected devices and the computer in which the plug-in card is
to be installed and disconnect all devices from the mains voltage by removing
the plug from the mains! Just turning off at the on/off switch is not enough!
• Open your computer's case and carefully remove the cover.
• Find a free Mini-PCIe-slot and insert the plug-in card.
If there are screws or other means of fi xation provided, fasten the plug-in card with screws or
clips.
• Connect the included mains cable for the plug-in card to the mains outlet (3, then you connect
it to the available free plug on the network card of your PC.
• Connect the two fl at plugs of the RS232 cable with the pin strips (1 and 2) on the plug-in card.
Make sure that the fl at plugs are correctly inserted.
• The two 9 pole RS232 plugs may e.g. be secured in suitable holes in the PC housing.
If necessary, fi x all cables with cable ties so that they cannot obstruct the fan of your computer.
• Close the computer housing.
• Connect your computer and monitor to the mains voltage again and switch on all devices.
• If your computer does not start correctly, switch it off immediately and check all the settings
and cable connections.
Before opening the PC again, disconnect the PC from the mains voltage, see above!
www.conrad.com
Version 08/11
6
3
5
4
Driver installation
• After Windows has started, it recognises the plug-in card automatically as new hardware.
• Insert the CD provided in the appropriate drive on your computer. Alternatively you may copy
the driver software on a memory stick from another computer; that is if your computer does
not have a disk drive.
• At the moment of publishing these instructions, the driver for the plug-in card was in the direc-
tory "PCIe IO", subdirectory "OXPCIe".
☞
A restart of Windows may be required after that, before the RS232 ports of the plug-
in card function properly.
Tips & Notes
• Only connect RS232 devices when the computer and the RS232 devices are switched off.
Otherwise, in some cases, the RS232 device as well as the plug-in card might be damaged!
• The interface name (e.g. COM3) is assigned automatically by Windows.
• Many notebooks have a separate Mini-PCIe slot, this is often used by the WLAN module.
In theory the plug-in card could be inserted here (after dismounting the WLAN module).
This, however, is not possible because of the cabling and the mains supply for the RS232
interface.
Disposal
Dispose of an unserviceable product in accordance with the relevant statutory
regulations.
1
2
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfi lming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2011 by Conrad Electronic SE.
Werbung
