Installation Instructions - Garmin STRIKER 5dv Installationsanweisung

Ice Fishing Kit Installation Instructions
Getting Started
Battery Information
Battery Warnings
The fishfinder device uses a user-replaceable, sealed, lead-acid
battery. If these guidelines are not followed, the battery may
experience a shortened life span or may present a risk of
damage to the device, fire, chemical burn, electrolyte leak,
and/or bodily injury.
• Do not place the battery near objects that may cause sparks,
flames, or heat.
• Do not incinerate the battery.
• Keep the battery tightly closed.
• Do not use a sharp object to remove the battery.
• Do not disassemble, puncture, or damage the battery.
• Do not swallow, touch, or inhale the contents of an open
battery. Avoid contact with internal acid. Contact with internal
acid may cause irritation or severe burns. Irritation may occur
to the eyes, respiratory system, and skin. Flush with water at
once if contact is made with acid.
• Do not submerge the battery and avoid contact with water.
• Do not short the battery terminals.
• Do not drop or throw the battery.
• Keep the battery away from children.
• Only replace the battery with the correct replacement battery.
Using another battery presents a risk of fire or explosion of
the device or charger.
• Only charge the battery with the included charger.
• Do not charge the battery in an unventilated area.
• Store in a cool, dry, and well-ventilated area.
• Do not charge the battery in a gas-tight container.
• Do not leave the device exposed to a heat source or in a
high-temperature location, such as in the sun in an
unattended vehicle. To prevent damage, remove the device
from the vehicle or store it out of direct sunlight.
• Do not use organic solvents or other cleaners other than
recommended chemical cleaners on the battery.
• Contact your local waste disposal department to dispose of
the battery in accordance with applicable local laws and
regulations.
• When storing the battery for an extended time, store within
the following temperature range: from 5° F to 104°F (from
-15° C to 40° C).
• Do not operate the battery outside of the following
temperature range: from 5° F to 122° F (from -15° C to 50°
C).
Charging the Battery
Ensure that you connect the correct connector to the correct
battery terminal. Damage to the battery, device, or bodily harm
may occur if the device is improperly connected to the battery.
Before you can charge the battery using the charger, you must
disconnect the device power cable from the positive and
negative terminals on the battery.
The battery is rechargeable and can be charged by connecting
the battery to a wall charger.
1
Connect the positive connector on the wall charger onto the
positive terminal on the battery.
2
WARNING
CAUTION
2
Slide the negative connector on the wall charger onto the
negative terminal on the battery.
3 Connect the wall charger to the wall outlet.
Battery Tips
• The life expectancy of a sealed lead acid battery can be
extended by recharging often and not completely discharging
the battery.
• Sealed lead acid batteries slowly lose their charge while in
storage. For best results, charge the battery prior to use.
• When used in cold temperatures, sealed lead acid batteries
do not hold the charge as long as in warmer temperatures.
• To avoid spilling the internal acid, keep the battery in the
upright position.
• Sealed lead acid batteries are completely recyclable.
Specifications
Battery type Sealed, lead acid
Battery life About 11 hr.
NOTE: The actual battery life of a fully
charged battery can vary based on the
temperature the battery is operated and
stored in, the age of the battery, and the
depth of the water.
Battery shelf life after 1 month: 92%
charging
3 months: 90%
6 months: 80%
Battery operating From 5° to 122°F (from -15° to 50°C)
temperature range
Battery charging From 5° to 104°F (from -15° to 40°C)
temperature range
Battery storage From 5° to 104°F (from -15° to 40°C)
temperature range
Physical size (assembled L × W × H: 10.629 in. × 10.629 in. ×
kit with device) 11.02 in. (270 mm × 270 mm × 280 mm)
Weight (unassembled kit 8.498 lb. (3855 g)
with device)
Assembling the Mount
You need a Phillips screwdriver to assemble the mount.
1 Insert the handle into the two openings on the portable
mount .
2
Attach the handle to the portable mount using two
M4×0.7×40 mm screws
3
Press the M6×1 nut into the bottom of the swivel-mount
base .
and M4×7 nuts .

Installation Instructions