Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
2)
Configure the Egon control unit in learning mode.
3)
Hold the Function button pressed for 10 seconds and then release it. The device sends to the learning request signal to the
control unit.
4)
If the repeater is correctly connected, the LED will flash twice to confirm receipt of the signal by the control unit.
5)
After the learning procedure, the repeater will be automatically learnt by the system. It is advisable to check that connection
and registration were completed correctly on the control unit as well.
R
e
m
o
v
i
R
e
m
o
v
i
The default settings must be restored in order to remove the repeater from the system to which it is connected. This operation
will reset the information relating to the current configuration and allow the device to connect on to the system again.
Before removing the device, make sure that the repeater is within the system signal range.
1.
Leave the control unit in off state.
2.
Hold the function button pressed for 10 seconds, then release it to reset the repeater.
3.
After resetting, the repeater will clear the system configuration and transmit a signal to the control unit so that it can be
removed from the system (it will no longer appear on the "Devices page").
T
e
c
h
n
i
c
T
e
c
h
n
i
c
Power supply: 110 – 230Vac, 50/60Hz
Backup power supply: internal, non-removable
Battery life: 6 hours (the value may vary depending on the conditions of use of the device and its configuration)
Two-way radio frequency 2.4 GHz
Working temperature range -10°C to +45°C
Dimensions: 55 mm x 55 mm x 66 mm
Weight: 300g
Conforming to EN 50131 Degree 2, Class Ⅱ
The manufacturer, URMET S.p.A., hereby declares that the wireless device: ZIGBEE ZB600RPT REPEATER complies with
Directive 2014/53/EU. The complete EU Declaration of Conformity can be downloaded from the following Internet address:
www.elkron.com.
DIRECTIVE 2012/19/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 4 July 2012 on waste electrical
and electronic equipment (WEEE).
The symbol of the crossed-out wheeled bin on the product or on its packaging indicates that this product must not be
disposed of with your other household waste.
Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point
for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at
the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health
and the environment.
For more information about where you can drop off your waste equipment for recycling, please contact your local city office,
your household waste disposal service or the shop where you purchased the product.
6
n
g
t
h
e
d
e
v
i
c
e
f
r
o
m
n
g
t
h
e
d
e
v
i
c
e
f
r
o
m
a
l
s
p
e
c
i
f
i
c
a
t
i
o
n
s
a
l
s
p
e
c
i
f
i
c
a
t
i
o
n
s
Simplified Declaration of Conformity
ELKRON
Tel. +39 011.3986711 - Fax +39
011.3986703
www.elkron.com
– mail to: info@elkron.it
t
h
e
s
y
s
t
e
m
(
r
e
s
t
o
t
h
e
s
y
s
t
e
m
(
r
e
s
t
o
r
e
d
e
f
a
u
l
t
s
e
t
t
i
n
g
s
r
e
d
e
f
a
u
l
t
s
e
t
t
i
n
g
s
ELKRON is a trademark of URMET S.p.A.
Via Bologna 188/C – 10154 Turin (TO) Italy
www.urmet.com
)
)
MADE IN TAIWAN
DS80WL58-001A
Werbung
Inhaltsverzeichnis
