Error Message Codes - JMA tph cloner Handbuch

6 ERROR MESSAGE CODES

the error and warning messages shown on the display are listed based on
the status of the process you are in.
if the list of quick solutions given below does not solve the related pro-
blem, a detailed study of the communication between the immobiliser ecu
and the transponder will be necessary.
the error / warning list and the possible solutions are shown below:
after display number 1 (checking transponder 1)
DISPlAY
No Chip cause
Press RD
or CP
solution
after display number 14 (checking transponder 2)
DISPlAY
No Chip cause
Press RD
or CP
solution
Wrong key cause
Press RD
or CP
solution
NOT blank cause
TPX3.
Delete?
solution
CP=YES
after display number 14 and with tPh_blanK (tPX3 in data capture mode
(sniff))
DISPlAY
Error !!!
cause
F8
solution
Error !!! cause
F3
solution
Fail cause
Press RD
solution
or CP
after display number 4, (checking data frames captured from ecu)
DISPlAY
No Chip cause 1
Press RD
or CP
solution
No Chip cause 2
Press RD
or CP
solution
20
DESCRIPTION
no signal from transponder, tP unk-
nown.
adjust position of tP on antenna,
check if new type of tP.
DESCRIPTION
no signal from transponder, unknown
tP.
adjust position of tP on antenna,
check new type of tP.
Philips crypto transponder detected.
reinsert a tPh-blanK.
tPh-crYPto or tPh-caPture de-
tected.
Press coPY to set tPh to data frame
capture mode.
Press read to cancel the operation.
DESCRIPTION
delete error whilst preparing tPh-
caPture.
adjust position of tP on antenna,
check trs rF signal
write error on Pag.3 of transponder
memory.
adjust position of tP on antenna,
check trs rF signal.
error in uid copy (writing of Pag. 0)
adjust position of tP on antenna,
check trs rF signal.
DESCRIPTION
transponder cannot pick up data frames
from vehicle's immobiliser because it is
unable to detect immobiliser's signal.
Position closer transponder on antenna
located in ignition cylinder.
transponder cannot pick up data fra-
mes from vehicle's immobiliser because
the immobiliser's protocol is not compa-
tible with PcF7936 (tP12).
it is necessary to study the protocol first
in order to be able to implement it.
Fail cause
Press RD
or CP
solution
after display number 9 (checking transponder 3)
DISPlAY
No Chip cause
Press RD
or CP
solution
Wrong key cause
Press RD
or CP
solution
Error !!! cause
FA
solution
Error !!! cause
FB
solution
Error !!! cause
FC
solution
after display dispX (reading data from key in Password mode)
DISPlAY
Error !!! cause
F9
solution
Error !!! cause
F2
solution
Error !!! cause
F4
solution
Error !!! cause
F5
solution
Error !!! cause
F6
solution
transponder not positioned properly or
removed too soon.
Position tPh-caPture correctly before
pressing coPY button (cP).
DESCRIPTION
no signal from transponder, unknown
tP.
adjust position of tP on antenna, make
sure that key inserted is original key
(Master).
tPh-crYPto or tPh-caPture detec-
ted.
insert right original key (Master).
error when inserting original key (Mas-
ter). (different uid).
reinsert the same original key (Master)
that was used in step 1.
all passwords picked up during capture
are incorrect.
start again from step 1, make sure that
the key responds to the commands from
the trs, watch cloner led.
all data captured (challenger-signatu-
re) are incorrect.
start again from step 1, make sure that
the key responds to the commands from
the trs, watch cloner led.
DESCRIPTION
data verification failure or these can-
not be read. data reading error on Page
0, Page 1 and Page 3. (Processing ratio
00%).
adjust position of tP on antenna, check
rF signal from trs.
data verification failure or these can-
not be read. data reading error on Page
2 (Processing ratio 50%).
adjust position of tP on antenna, check
rF signal from trs.
data verification failure or these can-
not be read. data reading error on Page
4 (Processing ratio 50%).
adjust position of tP on antenna, check
rF signal from trs.
data verification failure or these can-
not be read. data reading error on Page
5 (Processing ratio 50%).
adjust position of tP on antenna, check
rF signal from trs.
data verification failure or these can-
not be read. data reading error on Page
6 (Processing ratio 50%).
adjust position of tP on antenna, check
rF signal from trs.