Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
S
Y
S
T
E
M
S
T
A
T
E
L
E
D
(
G
R
S
Y
S
T
E
M
S
T
A
T
E
L
E
D
(
G
R
By pressing the
button, the system status will be checked:
Red LED on for 3 seconds: the system is in Total Armed state.
Red LED blinking for 3 seconds: the system is in Partial Armed state.
Green LED on for 3 seconds: the system is OFF.
The LED will flash green 4 times for the following cases:
No reply sent to control unit within 4 seconds.
Incorrect error code. If an incorrect disarming code is entered 5 times, the system will be blocked and the
keypad will be deactivated for approximately 9 minutes, during which normal operation cannot be restored
even if the correct disarming code is entered or by operating from the APP. Repeating an incorrect code
will extend the time by 9 more minutes.
Request to pass to Partial Armed state when the Total Armed state.
Forced arming request.
F
A
U
L
T
L
E
D
(
O
R
A
N
G
E
)
F
A
U
L
T
L
E
D
(
O
R
A
N
G
E
)
During the whole or partial system activation procedure:
Blinking 4 times: system error (control unit tamper, power fault, detector tamper, detector fault, door open, etc.)
On: alarms have occurred.
P
o
w
e
r
P
o
w
e
r
The remote keypad is powered by a CR2450 3V lithium battery.
The remote keypad can detect the battery state. If battery voltage is low, the keypad state LED will blink (green in Test mode or
orange in normal mode) during normal operation. The discharge battery signal is sent to the control unit during normal
transmission to view the respective state.
The battery is pre-installed in the factory.
E
n
e
r
g
y
s
a
v
i
n
g
m
o
E
n
e
r
g
y
s
a
v
i
n
g
m
o
The remote keypad is in stand-by mode and does not use current when it is not in use. It is activated for 5 seconds when any
button is pressed.
It switches off and goes back to stand-by mode if no button is pressed for 5 seconds.
After having entered a control, the remote keypad is switched off and goes back to stand-by mode.
T
e
s
t
m
o
d
e
T
e
s
t
m
o
d
e
The remote keypad may be set to test mode by entering the keypad code (default: 0000) followed by button
green state LED lights up and a long beep will sound.
To exit test mode, press the
switched off and the remote keypad will return to normal operating mode. Otherwise, the remote keypad will
automatically shut down Test mode after 5 minutes and go back to normal operating mode.
<
N
O
T
E
>
<
N
O
T
E
>
Test mode is useful to exclude the tamper alarm of the remote keypad during installation, during battery replacement or
if it is moved to another installation site.
When the remote keypad is in Test mode it is always active and will NOT switch off automatically after 5 seconds.
Test mode operation:
Press button
and then button 7 — The control unit transmits remote keypad learning data
Press button
and then button 2 — Panic alarm function on
Press button
and then button 5 — Panic alarm functions off (default)
Press button
and then button 6 — Change keypad code:
Enter the old remote keypad code and press the button
Enter the new 4-digit keypad code and press the button #.
Press button
Press button
and then button 8 — Arming mode without user code on.
Press button
and then button 9 — Arming mode with user code on (default).
<
<
N
N
O
O
T
T
E
E
>
>
Correct and received command: a long beep
Invalid or not received command: 4 short beeps.
DS1051-002B
E
E
N
/
R
E
D
)
:
E
E
N
/
R
E
D
)
:
d
e
d
e
button twice, the remote keypad will generate a long beep, the keypad state LED will be
twice — Exit Test mode.
. The
9
Werbung
Inhaltsverzeichnis
