Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
H
o
w
t
o
s
e
t
o
p
e
r
a
t
i
H
o
w
t
o
s
e
t
o
p
e
r
a
t
i
Arming can be enabled with or without entering the user code.
ARMING WITH USER CODE (DEFAULT SETTING = 1234)
In Test mode, press button
Total arming: enter a user code and press button
system state LED will light up and the keypad will beep.
Partial arming: enter a user code and press button
system state LED will blink four times and the keypad will beep three times. After pressing the button
seconds:
• Press 1 to activate the partition A.
• Press 2 to activate the partition B.
• Press 3 to activate the partition C.
If no button is pressed, the partialisation chosen during learning will be activated.
In partial activation status, it will be possible to activate a further partition, by entering the user code followed by the
button
and by the button relating to the partition to be added.
EXAMPLE: in activation state A, if you want to add B, type: user code +
activate.
EXAMPLE: in activation state A+B, if you want to add also C, type: user code +
B + C will activate.
Disarming: enter a user code and press button
light up and the keypad with beep twice.
ARMING WITHOUT USER CODE
In Test mode, press button
Total arming: press button
up and the keypad will beep.
Partial arming: press button
blink four times and the keypad will beep three times. After pressing the button
• Press 1 to activate the partition A.
• Press 2 to activate the partition B.
• Press 3 to activate the partition C.
If no button is pressed, the partialisation chosen during learning will be activated.
In partial activation status, after pressing the button
further partialisation (for example: in the activation state A, the pressure of the key 2 will activate B, realizing the
state A + B. A further pressure of the key 3 will activate A + B + C.
Disarming: enter a user code and press button
light up and the keypad with beep twice.
Panic alarm
Press buttons 1 and 3 to activate the panic alarm (if enabled). Press the user code to disarm it.
<
N
O
T
E
>
<
N
O
T
E
>
In default configuration, the panic alarm is off.
Main function overview
If alarms are stored, the green state LED and the fault LED will light up and the keypad will beep five times.
Activate Test mode — Enter the keypad code and press button
Panic alarm — Press buttons 1 and 3 at the same time (if the function is activated).
Check control unit state — In normal operating mode, press button
Red LED on: the system is in Total Armed state.
Red LED blinking: the system is in Partial Armed state.
Green LED on: the system is in Disarmed state.
Green LED blinking: error for the following reasons:
No reply sent to control unit within 4 seconds.
Incorrect code.
Request to pass to Partial Armed state when the Total Armed state.
Forced arming request.
DS1051-002B
n
g
m
o
d
e
n
g
m
o
d
e
and then button 9 to enable arming with user code (default).
and then button 8 to enable arming without user code.
. If there are no faults and arming was successful, the red system state LED will light
. If there are no faults and arming was successful, the red system state LED will
. If there are no faults and arming was successful, the red
. If there are no faults and arming was successful, the red
. If disarming was successful, the green system state LED will
, within 2 seconds: the pressure of a key can activate a
. If disarming was successful, the green system state LED will
.
.
, within 2
+ 2 (within 2 seconds). A + B will
+ 3 (within 2 seconds). A +
, within 2 seconds:
11
Werbung
Inhaltsverzeichnis
