Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
H
o
w
t
o
c
h
a
n
g
e
t
h
e
H
o
w
t
o
c
h
a
n
g
e
t
h
e
I.
Set the Tamper alarm to Total on the control unit or activate Test mode as described above.
II.
Remove the remote keypad by loosening the closing screw.
III.
Extract the flat battery and press any button to discharge the device completely before inserting the new battery in the
housing with the side free from markings (negative) facing downwards.
IV.
Close the housing using the rear fixing screws.
V.
Refit the remote keypad by tightening the closing screw.
VI.
Restore normal operation on the control unit.
F
a
u
l
t
s
F
a
u
l
t
s
IN NORMAL OPERATING MODE:
If after entering a user code and pressing the Disarming button, the orange LED lights up with two beeps, it
a)
means that the system does not show any anomalies. If there are anomalies, the keypad will emit 5 beeps
instead and the green LED will light up first and then the orange LED will flash for 5 seconds.
b)
If the system is already being armed, partial arming using the remote keypad is NOT possible. The control unit
signals this situation by turning on the orange LED and emitting 3 beeps (active system), then with 2 beeps, the
green LED lights up and then with the flashing orange one (transmission error).
c)
In the event of activation with a fault, the keypad will emit 3 beeps and the orange LED will light up. Then the
green LED will light up and then the orange LED will flash 4 times.
R
e
s
t
o
r
i
n
g
d
e
f
a
u
l
t
s
R
e
s
t
o
r
i
n
g
d
e
f
a
u
l
t
s
The remote keypad can be reset with the default values and restarted if the keypad code is forgotten or the remote keypad
displays a problem.
Step 1 Remove the battery.
Step 2 Hold button 3 pressed and insert the battery.
Step 3 Hold button 3 pressed until the keypad beeps 3 times.
Step 4 Release button 3: the reset procedure is done.
<
N
O
T
E
>
:
<
N
O
T
E
>
:
The keypad code returns to the default setting 0000 after resetting.
T
e
c
h
n
i
c
a
l
s
p
e
c
i
f
i
c
a
T
e
c
h
n
i
c
a
l
s
p
e
c
i
f
i
c
Power supply: 1 lithium battery CR2450 3V
Battery life: 5 years (typical value, may vary according to use)
Two-way radio frequency: 868 MHz
Working temperature range -10°C to +45°C
Dimensions: 80 mm x 116 mm x 20.5 mm
Weight: 100g
Certification EN 50131 Grade 2, Class
Hereby, URMET S.p.A. declares that the radio equipment type: LED REMOTE KEYPAD 1051/025 is in compliance with Directive
2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.urmet.com.
12
b
a
t
t
e
r
y
b
a
t
t
e
r
y
e
t
t
i
n
g
s
e
t
t
i
n
g
s
t
i
o
n
s
a
t
i
o
n
s
Ⅱ
SIMPLIFIED EU DECLARATION OF CONFORMITY
DS1051-002B
Werbung
Inhaltsverzeichnis
