Werbung
Verfügbare Sprachen
Verfügbare Sprachen
®
HDMI™ Transmission Set
GB
Please read these operating instructions carefully
prior to operation and keep them for later refer-
ence.
1
Applications
This transmission set consisting of two signal con-
verters is designed for transmitting HDMI™ signals
via Cat 5 or Cat 6 network cable. Thus, for a reso-
lution of 1080i / 720p, the connection cable may
have a length of up to 70 m. The signal converters
are compatible with HDMI™ 1.3 standard and sup-
port 3D signals. By means of an HDMI™ to DVI
adapter, transmission of a DVI signal is also possi-
ble.
2
Safety Notes
The units (signal converters and power supply
units) correspond to all relevant directives of the
EU and are therefore marked with
WARNING The power supply units use danger-
ous mains voltage. Leave servicing
to skilled personnel only. Inexpert
handling may result in electric shock.
Please observe the following items in any case:
G
The units are suitable for indoor use only. Pro-
tect them against dripping water and splash
water, high air humidity and heat (admissible
ambient temperature range: 0 – 40 °C).
G
Do not operate the signal converters and imme-
diately disconnect the corresponding power sup-
ply unit from the socket
1. if one of the units is visibly damaged,
2. if a defect might have occurred after a unit
was dropped or suffered a similar accident,
3. if malfunctions occur.
In any case the units must be repaired by skilled
personnel.
G
For cleaning only use a dry, soft cloth; never use
water or chemicals.
G
No guarantee claims for the units and no liability
for any resulting personal damage or material
damage will be accepted if the units are used for
other purposes than originally intended, if they
are not correctly connected or operated, or if
they are not repaired in an expert way.
If the units are to be put out of operation
definitively, take them to a local recycling
plant for a disposal which is not harmful to
the environment.
1
2
3
4
5
HDEXT-600
3
Installation and Operation
To install the signal converters (e. g. on a wall), fas-
ten them with screws via the two mounting brack-
ets (1) of each unit.
1) Connect the audio / video source to the jack
HDMI IN (4) on the front of the
2) Connect the unit for processing the signal (e. g.
monitor) to the jack HDMI OUT (7) on the front
Receiver
of the
3) Connect the jacks LINK (6) of the type RJ45
(8P8C), each on the rear of the transmitter and
the receiver, by means of an unshielded Cat 5 or
Cat 6 cable (UTP) [e. g. "CAT-5100UTP" from
MONACOR]. The contacts of the RJ45 plugs
must be connected straight through.
Image resolution to be obtained:
Cat 6, cable length up to 50 m: 1080p
Cat 6, cable length up to 70 m: 1080i / 720p
Cat 5, cable length up to 40 m: 1080p
4) To select one of the two predefined signal for-
mats, set the DIP switch (5) on the
.
No. 1 to the position OFF↑ and then use switch
No. 2 to select the format:
OFF↑ Video: 1080i, audio channels: 2, LPCM
ON↓
If the monitor used requires another format, the
required format can be determined automati-
cally: Temporarily connect the monitor to the
input HDMI IN (4) of the
the following:
a) Set the DIP switch No. 1 to the position ON↓.
b) Switch on the monitor.
c) Connect one of the plug-in power supply
units provided to the low voltage jack "DC
5 V" (2) on the transmitter and to a mains
socket (230 V~/ 50 Hz). The power LED ON
(3) of the transmitter will light up briefly and
will then start to flash. The signal format
received from the monitor will now be saved
on the transmitter.
d) Disconnect the transmitter from the power
supply.
e) Connect the monitor to the output HDMI OUT
(7) of the receiver and connect the signal
source to the input HDMI IN (4) of the trans-
mitter.
To use the signal format saved (automatically
determined), set the DIP switch No. 1 to the
position ON↓.
5) Connect the plug-in power supply units provided
to the low voltage jack "DC 5 V" (2) each on the
1
6
®
MONACOR INTERNATIONAL GmbH & Co. KG • Zum Falsch 36 • 28307 Bremen • Germany
Copyright
©
by MONACOR INTERNATIONAL. All rights reserved.
Order No. 18.3350
Transmitter
.
Transmitter
Video: 1080p, audio channels: 5.1, LPCM
Transmitter
and then do
1
transmitter and on the receiver, then connect
them to a mains socket (230 V~ / 50 Hz). Thus,
the units are switched on; the power LEDs ON
(3) light up.
For cables with a length of up to 30 m, no sepa-
rate power supply unit for the receiver is
.
required; the transmitter will supply the receiver
with power via the data cable. The power LED
ON of the receiver will only light up when a
power supply unit is connected.
To prevent interference during transmission: While
laying the cable, make sure that its distance to
units or cables with electromagnetic fields (e. g.
microwaves, wireless transmitters, mains cables)
is sufficient.
3.1 LEDs of the jacks LINK
The LEDs at the jacks LINK (6) indicate the follow-
ing:
Transmitter
Green: data and supply voltage are being provided
Yellow: no video data available or wrong signal
format
Receiver
Green: supply voltage and data are being received
Yellow: no data reception or signal too weak
4
Specifications
HDMI™ input / output: . . jack, type A
Input level
TMDS signal: . . . . . . . 1.2 V
DDC signal: . . . . . . . . 5 V
Max. data rate: . . . . . . . 2.25 Gbit/s
Image resolution: . . . . . 480i / p, 720p, 1080i / p
Power supply
Transmitter: . . . . . . . . 5 V /1.2 A
Receiver: . . . . . . . . . . 5 V / 0.7 A
via PSUs provided, connected to 230 V~ / 50 Hz
Ambient temperature: . . 0 – 40 °C
Dimensions
Transmitter: . . . . . . . . 91 × 67 × 27 mm
Receiver: . . . . . . . . . . 120 × 67 × 27 mm
Weight
Transmitter: . . . . . . . . 140 g
Receiver: . . . . . . . . . . 175 g
Subject to technical modification.
7
1 2
A-1399.99.02.12.2013
PP
PP
at 24 / 50 / 60 Hz
3
6
Werbung
