Electrical Safety - Defort DAC-1550 Bedienungsanleitung

• Children and animals should be kept far away from
the area of operation of the machine.
• If you use the compressor to spray paint:
a) Do not work in enclosed spaces or near naked
À ames.
b) Make sure that the environment in which you will
be working has dedicated ventilation.
c) Protect your nose and mouth with a dedicated
mask (¿ g. 21)
• Do not use the compressor when the electrical cable
or he plug is damaged, and instruct an authorised
Support Service to replace them with an original
part.
• When the compressor is placed on a surface higher
than the À oor, it should be secured to prevent it from
falling down during operation.
• Do not put objects or your hands in the protective
covers to avoid physical damage and damage to the
compressor.
• Do not use the compressor as a blunt instrument
against persons, objects or animals in order to pre-
vent serious damage.
• If the compressor is no longer in use, always take
the plug out of the plug socket.
• Always make sure that compressed-air hoses are used
for compressed air and which are characterised by a
maximum pressure adjusted to that of the compressor.
Do not try to repair the hose if it is damaged.

ELECTRICAL SAFETY

Earthing regulations
This compressor has to be earthed while in use
in order to protect the operator against electrical
shocks. The compressor is provided with a two-
core cable plus an earth.
The electrical connection has to be made by a quali¿ ed
technician. We recommend never disassembling the
compressor and neither making any other connections
into the pressure regulator. Repairs should be carried
out by authorised Support Services or by other qual
i¿ ed centres.
Never forget that the earthing core is the
green or the yellow/green wire. Never
connect this green wire to a terminal under
load.
Before replacing the plug of the feed, make sure that
the earth cable is connected. If in doubt, please call in a
quali¿ ed electrician and have the earthing checked.
Extension cables
Only use an extension cable with a plug and earth,
so never use damaged or À attened extension cables.
Check whether the extension cable is in a good condi-
tion. For this device the extension cable should have a
diameter of at least 2.5 mm
length of 20 metres). Always unroll extension cables
fully before using them.
2 (this applies to a maximum
Electrical connection
Always check whether the input voltage of the motor
corresponds to the mains voltage indicated on the
speci¿ cation plate.
The compressors are supplied with an electrical cable
and a two-pole plug + earth. It is important to connect
the compressor with an earthed plug socket, (¿ g. 9)
Note! Never use the earth-wire instead of the
neutral (0-wire). The earthing should take
place in accordance with accidentprevention
regulations (EN 60204).
3. USE
For homehold use only
NB:
The information you will ¿ nd in this manual has been
written to assist the operator in the use and mainte-
nance of the compressor. Some illustrations in this
manual show details which may differ from those of
your compressor.
INSTALLATION
After having taken the compressor out of its packaging
(¿ g. 1) and having checked that it is in perfect condi-
tion, and having noted that no damage occurred during
transport, the following acts should be performed.
If not yet ¿ tted, ¿ t the wheels and rubber cap on the
tank according to the instructions represented in ¿ g. 2.
Place the compressor on a À at surface or at a maxi-
mum slope of 10° (¿ g. 3), in a well ventilated area,
protected against atmospheric factors and not in ex-
plosive surroundings. If the surface area is sloping and
smooth, make sure that the compressor will not move
when in operation, otherwise block the wheels with two
wedges. If the surface area is aboard or a shelf of a
bookcase, just make sure that they cannot fall down
by securing them properly. For proper ventilation and
effective cooling, it is important that the compressor is
positioned at least 100 cm from the wall (¿ g. 4).
Make sure that the compressor is transported
in the right way, do not turn it upside down
and don't lift it with hooks or ropes (fig. 5-6).
STARTING UP
• Check whether the mains voltage corresponds to
that indicated on the electrical speci¿ cation plate
(¿ g. 10), the permitted tolerance range should be
within 5%.
GB
9