M+W Instruments Superlite 1300 Bedienungsanleitung Seite 9

factors may damage the plastic parts of the unit.
6. cleaning agents should not enter the unit as this may short-circuit the unit or cause potentially dangerous malfunction.
7. only factory-authorized technicians are authorized to open and repair the unit.
8. only original M+W superlite 1300 spare parts should be used to replace defective parts. the unit warranty does not cover any damage resul-
ting from the use on non-original replacement parts. the unit or any of its parts should not be dis-assembled while it is connected to the mains!
9. Prior to every application, the light conductor, the glare protection shield and the light protection cap should be prepared according to the
recommendations in VI. care and maintenance.
10. fraGILe! Be extremely careful during transportation, storage and handling of the unit!
11. Pursuant to Directive 2002/96/ec, this symbol shows that the product must not be disposed of as urban waste at the end of its operating
life. the product must be taken to centers specialized in separate collection of electric and electronic equipment. correct disposal of the equip-
ment, which is no longer used, prevents negative consequences for the environment and human health!
V. PREPARATION AND SEQUENCE OF OPERATION
M+W superlite 1300 is designed for use as a free - standing table unit.
1. take the curing light M+W superlite 1300 out from the packing.
Attention! the unit should be placed at least 1 meter away from any heat source.
2. Prior to being used for the first time, the light conductor, the glare protection shield and the light protection cap should be prepared accor-
ding to the recommendations in VI. care and maintenance.
3. connect the power adapter to the mains outlet.
4. the cordless handpiece must be fully charged before staring work for the first time. for this purpose, charge it for at least 10 hours. new Li-
Ion batteries attain full capacity only several charging / discharging cycles. therefore, the battery charge may initially be sufficient for a smaller
number of exposures only.
5. M+W superlite 1300 is equipped with 4 curing modes that guarantee full and fast hardening of the restorative material. select the curing
mode by pressing the button MoDe on the digital panel of the handpiece. Press repeatedly until the
desired curing mode is selected:
A – RAMP L – LONG F – FAST P – PULSE
RAMP mode (10 - 20 - 30 sec.) - During the first 3 sec. light intensity slowly increases from 0% to 100% of the light intensity (soft start) to
avoid stress in the restorative material.
LONG mode (9 min.) suitable for long work and bleaching. there is audible signal every 1 min. the curing light works continuously for 9 min.
or until the start/stop button is pressed again. In this curing mode light intensity is at maximum level.
FAST mode (10 sec.) - emitted light has highest intensity - 100% of the light intensity to achieve full hardening of the photocomposite.
PULSE mode (10 - 20 - 30 sec.) - there are consecutive light emitting and pause that help to avoid shrinking in restorative material without
extending exposure time.
select exposure time by pressing "TIMER" button repeatedly. the horizontal line shows selected time - 10, 20 or 30 sec.
6. the unit is activated by pressing the start/stop button of the handpiece. after the unit is activated, countdown timer is
seen on the digital display. an audible beeper on every 10 sec is heard.
7. Direct the emitting light of handpiece to the curing spot at the closest distance (4-7 mm) and make sure the lightguide does not touch the
photocomposite during the first several seconds and after that, when surface layer is hardened enough, the lightguide can touch the photo-
composite.
8. after second pressing of the start/stop button or after elapsing the pre-selected time (10, 20 or 30 sec ) the unit stops.
If an additional curing cycle is necessary, the unit may be activated repeatedly. In the end return the handpiece to the
charging station.
9. switching off of curing light in the end of the day shall be done by unplugging of adapter from the wall socket.
10. "BeePer on/off" functIon". this function allows to switch on and off the beeper. Hold MoDe button for 5-6 sec., beeper indication ap-
pears and beeper is changed automatically to opposite: If beeper is on - after holding MoDe button, off will be displayed and beeper will be
switched off. If beeper is off - after holding MoDe button, on will be displayed and beeper will be switched on.
9