Other Features - Samsung LE32C570 Bedienungsanleitung

Satellite System Setup
The PIN input screen appears. Enter your 4 digit PIN number.
Satellite System Setup is available when Antenna is set to
Satellite. Before running Auto Store, set Satellite System Setup.
Then channel scan is run normally.
Satellite Selection: You can choose the satellites for this TV.
■
LNB Power (Off / On) : Enables or disables the power
■
supply for the LNB.
LNB Settings : Configures the outdoor equipment.
■
Satellite: Selects the satellite for receiving digital
broadcasts.
Transponder: Selects a transponder from the list or adds a
new transponder.
DiSEqC Mode: Selects DiSEqC mode for the selected LNB.
Lower LNB Oscillators: Sets the LNB oscillators to a lower
frequency.
Upper LNB Oscillators: Sets the LNB oscillators to a higher
frequency.
Tone 22 khz (Off / On / Auto): Selects the Tone 22 kHz
depending on the LNB type. For a universal LNB it should
be Auto.
Signal Quality: Display the current status of broadcasting
signal.
Positioner Settings : Configures the antenna positioner.
■
Positioner (Off / On): Enables or disables the positioned
control.
Positioner Type (USALS / DiSEqC 1.2): Sets the
positioned type between DiSEqC 1.2 and USALS(Universal
Satellite Automatic Location System).
–
My Longitude : Sets the longitude for my location.
–
My Latitude : Sets the latitude for my location.
–
Satellite Longitude Settings: Sets the longitude of user
defined satellites.
User Mode: Sets the position of satellite antenna according
to each satellite. If you store the current position of satellite
antenna according to a certain satellite, when the signal of
that satellite is needed, the satellite antenna can be moved
to pre-populated position.
–
Satellite : Selects the satellite to set the position for.
–
Transponder : Selects a transponder from the list for
signal reception.
–
Moving Mode : Selects the movement mode between
discrete and continuous movement.
–
Step Size : Adjusts the step size degrees for the antenna
rotation. Step Size is available when Moving Mode is set
to Step.
–
Go to Stored Position
stored satellite position.
–
Antenna Position : Adjusts and stores the antenna
position for the selected satellite.
–
Store Current Position
selected positioner limit.
–
Signal Quality : Display the current status of
.
broadcasting signal
: Rotates the antenna to the
: Stores current position as the
Installer Mode: Sets limits to the scope of movement of
satellite antenna or reset the position. Generally, installation
guide uses this function.
–
(East / West): Selects the direction of
Limit Position
the positioner Limit.
–
Antenna Position : Adjusts and stores the antenna
position for the selected satellite.
–
Store Current Position
as the selected positioner Limit.
–
Go to Zero : Moves the antenna to the reference
position.
–
Reset Positioner Limit
over the full arc.
Reset All Setting (OK / Cancel)
■
be reset to the initial values.
Editing channels
¦
Channel Manager Option Menu
(in Channel Manager)
1. Select a channel and press the
2. Edit the channel name or number using the Edit
Channel Name or Edit Channel Number menu.
Edit Channel Name (analogue channels only): Assign
■
your own channel name.
(digital channels only): Edit the
Edit Channel Number
■
number by pressing the number buttons desired.

Other Features

¦
Cable Search Option
(depending on the country)
Sets additional search options such as the frequency and
symbol rate for a cable network search.
Freq.Start / Freq.Stop : Set the start or stop frequency
■
(differs in each country)
: Displays available modulation values.
Modulation
■
Symbol Rate : Displays available symbol rates.
■
: Stores the current position
: Allows the antenna to rotate
: All satellite settings will
TOOLS button.
13
English