Herunterladen Inhalt Inhalt Diese Seite drucken

Maintenance; Optional Accessories - Makita WUT02 Betriebsanleitung

Funk-netzadapter
Vorschau ausblenden Andere Handbücher für WUT02:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 47
Troubleshooting for wireless activation function
Before starting the troubleshooting, check following:
The wireless unit is installed into the adaptor.
The adaptor is plugged into the outlet of the vacuum cleaner.
Conduct your own inspection first before asking for repairs. Also refer to the troubleshooting section of tool's instruction manual.
If you find a problem that is not explained in the manual, do not attempt to dismantle the tool. Instead, ask Makita
Authorized Service Centers, always using Makita replacement parts for repairs.
State of abnormality
Cannot finish tool registration / can-
celling tool registration successfully.
The vacuum cleaner does not run
along with the switch operation of
the tool.
Cannot erase all tool registrations
The vacuum cleaner automatically
runs when;
- Plugging the adaptor to the vacuum
cleaner or;
- Changing the stand-by switch on
the vacuum cleaner to "AUTO".
NOTE: On some cleaners, the stand-by switch "AUTO" is described as an icon or different word. In this case, set
the vacuum cleaner to auto start/stop function.

MAINTENANCE

CAUTION:
Always be sure that the adaptor is
unplugged before attempting to perform inspec-
tion or maintenance.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
Probable cause (malfunction)
The tool registration procedures for the
tool or adaptor has not been finished.
The wireless activation button on the
tool has not been pushed.
The stand-by switch on the vacuum
cleaner is not set to "AUTO".
The tool and adaptor is away from each
other (out of the transmission range).
Incorrect channel setting
Using a vacuum cleaner which is not
supported.
More than 10 tools are registered to
the adaptor.
The adaptor erased all tool
registrations.
Pressing the wireless activation button
on the tool.
The stand-by switch on the vacuum
cleaner is not set to "AUTO".
The wireless activation button is not
held down correctly.
The detecting method of vacuum clean-
er's auto start/stop function.
8 ENGLISH
Remedy
Perform the tool registration procedures for both the
tool and the adaptor at the same timing.
Push the wireless activation button briefly and make
sure that the wireless activation lamp is blinking in blue.
Set the stand-by switch on the vacuum cleaner to
"AUTO".
Get the tool and adaptor closer each other. The max-
imum transmission distance is approximately 10 m
however it may vary according to the circumstances.
The current channel setting is not appropriate for
the vacuum cleaner being used. Refer to "Channel
setting" for how to configure.
Use a Makita cleaner with auto start/stop function.
Perform the tool registration again.
If more than 10 tools are registered to the adaptor, the
tool registered earliest will be cancelled automatically.
Perform the tool registration again.
Press the wireless activation button on the adaptor
for erasing all tool registrations.
Set the stand-by switch on the vacuum cleaner to
"AUTO".
Hold down the wireless activation button for more than 6
seconds and then release it when the wireless activation
lamp blinks in red. Hold down the wireless activation button
for more than 6 seconds again until the wireless activation
button rapidly blinks in red and then release the button.
If the vacuum cleaner stops running in a few seconds,
you can use the wireless activation function as usual.
If the vacuum cleaner continues to run for 20 sec-
onds or longer, and you can stop it by unplugging
the adaptor, the malfunction of the adaptor can be
thought. Contact our authorized service center.

OPTIONAL ACCESSORIES

CAUTION:
These accessories or attachments
are recommended for use with your Makita tool spec-
ified in this manual. The use of any other accessories
or attachments might present a risk of injury to persons.
Only use accessory or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
Wireless unit
NOTE: Some items in the list may be included in the
tool package as standard accessories. They may
differ from country to country.

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Wut02u199773-1

Inhaltsverzeichnis