Tool Specifications; Declaration Of Conformity; Noise/Vibration Information; Battery Charging - Würth SBS 10-A Originalbetriebsanleitung

Tool Specifications

Sabre saw
Art. No.
Rated voltage
Stroke rate at no load n
Stroke
Cutting depth, max.
– in wood
– in non-alloy steel
– pipe diameter
Weight according to
EPTA-Procedure 01/2003

Noise/Vibration Information

Measured sound values determined according to EN 60704.
Typically the A-weighted sound pressure level of the product
is 70 dB(A). Uncertainty K=3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values a
h
determined according to EN 60745:
Cutting board: a =8.0 m/s
h
Cutting wooden beam: a
The values given for sawing particle board apply for a workpiece thick-
ness of 20 mm.
The vibration emission level given in this information sheet has
been measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with another.
It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main appli-
cations of the tool. However if the tool is used for different appli-
cations, with different accessories or poorly maintained, the
vibration emission may differ. This may significantly increase the
exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or when
it is running but not actually doing the job. This may significantly
reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from
the effects of vibration such as: maintain the tool and the acces-
sories, keep hands warm, organise work patterns.
0700 202 X
V=
-1
min
0
mm
mm
mm
mm
kg
(triax vector sum) and uncertainty K
2 2
, K=1.5 m/s ,
2
=12.0 m/s , K=1.5 m/s
h

Declaration of Conformity

We declare under our sole responsibility that the product
SBS 10-A
described under "Tool Specifications" is in conformity with the
following standards or standardization documents:
10.8
EN 60745 according to the provisions of the directives
0–3000
2009/125/EC (Regulation 1194/2012), 2011/65/EU,
14.5
2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:
65
Adolf Würth GmbH & Co. KG, PFW,
8
Reinhold-Würth-Straße 12-17
50
74653 Künzelsau, Germany
1.2
T. Klenk
General Manager
Künzelsau: 27.06.2013
Note: The battery is supplied partially charged. To ensure
2
.
full capacity of the battery, completely charge the battery in
the battery charger before using your power tool for the first
time.
The lithium ion battery can be charged at any time without
reducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
 Do not continue to press the On/Off switch
after the machine has been automatically
switched off. The battery can be damaged.
The battery is equipped with a NTC temperature control
which allows charging only within a temperature range of
between 0 °C and 45 °C. A long battery service life is
achieved in this manner.
Observe the notes for disposal.
Removing the battery (see figure A)
• To remove the battery 12 press the unlocking buttons 5
and pull out the battery downwards. Do not exert any
force.
A. Kräutle
General Manager

Battery Charging

15