Product Description - 3M DBI-SALA Flexiguard M100 H-Base Handbuch

;
Before using this equipment, record the product identification information from the ID label in the "Inspection and
Maintenance Log" at the back of this manual.
;
Always ensure you are using the latest revision of your 3M instruction manual. Visit the 3M website or contact 3M
Technical Services for updated instruction manuals.

PRODUCT DESCRIPTION:

Figure 1 illustrates the 3M™ Flexiguard™Modular Jib System M100 H-Base. The H-Base is designed to be used with approved
Flexiguard Modular Jib System M100 Masts. The system is free standing and does not require any additional counterweight.
The H-Base allows for vehicles to drive over the Outrigger Legs to get them closer to the Mast so the user can work on top of
vehicles.
Figure 2 illustrates components of the H-Base. See Table 1 for Component Specifications. The Hitch Ball Post (A) is the receiver
to mount the approved 3M Flexiguard M100 Mast. The Outrigger Legs (D) provide support for the H-Base and are connected by
the Main Center Base (B) where the Level Indicators (C) are located. Use the Level Indicators to check that the system is within
the +/- 1° of allowable slope. The Lifting Channels (E) are used to transport the H-Base with a forklift, pallet jack, crane, etc.
System Specifications:
Compatibility:
Standards:
Capacity:
Product Weight:
Resting Structure
Requirements:
Maximum Arresting Force:
Component Specifications:
Figure 2
Component
Reference
A
Hitch Ball Post
B
Main Center Base
C
Level Indicators
D
Outrigger Legs
E
Lifting Channels
1.0 PRODUCT APPLICATION
1.1 PURPOSE: The H-Base is designed for use as a component of a Fall Arrest System.
1.2 DESCRIPTION: The Floor Mount Base (Figure 1) is designed to rest on flat ground and be used as a mounting point for
3M™ DBI-SALA® Flexiguard™ Modular Jib System M100.
1.3 STANDARDS: The H-Base conforms to the national or regional standar(s) identified on the front cover of these
instructions. If this product is resold outside the original country of destination, the re-seller must provide these
instructions in the language of the country in which the product will be used.
1.4 SUPERVISION: Installation of this equipment must be supervised by a Qualified Person
supervised by a Competent Person
1.5 TRAINING: It is the responsibility of users of this equipment to understand these instructions and be trained in correct
installation, use, and maintenance of this equipment. Users must be aware of the consequences of improper installation
or use of this equipment. This instruction manual is not a substitute for a training program. Training must be provided on
a periodic basis to ensure user proficiency.
1.6 RESCUE PLAN: When using this equipment and connecting subsystem(s), the employer must have a rescue plan and
the means at hand to implement and communicate that plan to users, authorized persons
site rescue team is recommended. Team members should be provided with the equipment and techniques to perform a
successful rescue. Training should be provided on a periodic basis to ensure rescuer proficiency.
1 Qualified Person: A person with a recognized degree, certificate, or professional standing, or who by extensive knowledge, training, and experience has successfully
demonstrated their ability to solve or resolve problems relating to fall protection and rescue system to the extent required by applicable national, regional, and local
regulations.
2 Competent Person: One who is capable of identifying existing and predictable hazards in the surroundings or working conditions which are unsanitary, hazardous, or
dangerous to employees, and who has authorization to take prompt corrective measures to eliminate them.
3 Authorized Person: A person assigned by the employer to perform work a a location where the person could be exposed to a fall hazard.
4 Rescuer: A person using the rescue system to perform an assisted rescue.
Table 1 – Specifications
The H-Base covered in this instruction are compatible with 3M™ DBI-SALA® Flexiguard™ Modular Jib
System M100.
Designed and tested to meet the requirements of EN795:2012 (Type B), OSHA 1926.502, and OSHA
1910.140.
See 3M DBI-SALA Flexiguard Modular Jib System M100 instructions 5908371.
1335 lb. (605 kg)
Structure supporting the Fall Arrest System must withstand a 4,035 lb. (1,830 kg) + weight of jib vertical
load.
All connecting systems (SRD, Energy Absorbing Lanyards, etc.) used with the system must limit the
maximum arresting force to 1,350 lbf (6 kN).
.
2
Materials
Steel
Steel
Plastic
Steel
Steel
7
. Use of this equipment must be
1
, and rescuers . A trained, on-
3 4