Herunterladen Diese Seite drucken
Vorschau ausblenden Andere Handbücher für Standard:

Werbung

MODEL
STANDARD

Werbung

loading

Inhaltszusammenfassung für IVY DESIGN Standard

  • Seite 1 MODEL STANDARD...
  • Seite 2: Maintenance

    Warning Look for the right Before you start unpacking and mounting your table make sure that no children are spot to mount your around. Small parts as screws can be swallowed. The table has to be fi xed properly to the wall by an expert. table: Children are not allowed to fold up or down the table themselves! When you fold up or down your table babies/children must be out of reach!
  • Seite 3: Montage

    2 x Upper Wall Mount Scope of delivery: 1 x Lower Wall Mount 2 x Upper Wall Mount 2 x Lower Wall Mount 4 x Bolt / Table Leg Lock Bar + Upper Lock Bar 2 x Pivot / Lower Wall Mount 1 x Allen Key for Pivots 4 x Hinge / Table Legs Drill holes at the green marked spots: 4 holes for the Lower Wall Mount,...
  • Seite 4 Fix the table legs, lift the table up and slide the grooves on the table surface into the Lower Wall Mount on the wall. Screw in the bolts with an Push the Upper Wall Mount Lock Bars totally into the side of the table top Allen key on both sides of the table.
  • Seite 5 To lock the table legs insert the Bolts on either side of the table. The bolts can serve you as clothes hooks. Now your IvyDesign Model Standard is locked and ready to use. Um die Tischbeine zu arretieren, müssen die beiden Stahlstifte, IvyDesign Modell Standard ist gesichert und kann jetzt benützt werden.
  • Seite 6 Manual Anleitung Before folding up the table remove the bolts. Bevor der Tisch nach oben geklappt wird, müssen die Stahlstifte entfernt werden.
  • Seite 7 Lift the table until it‘s parallel to the wall. Lift up the table. Heben Sie den Tisch bis die Tischfl äche parallel zur Wand positioniert ist. Heben Sie den Tisch an.
  • Seite 8 Push the Upper Wall Mount Lock Bars outwards into the Upper Metal Lock. Insert the bolts into the picture frame. Schieben Sie den Oberen Riegel der Stecken Sie die Stahlstilfte in den Bilderrahmen. Wandbefestigung nach außen in die Metallschließe.
  • Seite 9 For Model Standard with plexiglass: For Model Standard with plexiglass: Exchange the Poster Exchange the Poster Für Modell Standard mit Plexiglas: Für Modell Standard mit Plexiglas: Austausch des Posters Austausch des Posters The Bolts can be used to hang up your cloths.
  • Seite 10 When the lower piece of the frame is released you are able to slide off the Knock softly on the right lower piece of the frame with your hand perspex protection sheet and insert/exchange your poster/photo. in order to release this part. Wenn der untere Rahmenteil gelöst ist, können Sie Klopfen Sie vorsichtig auf die innere Seite des unteren Teil des das Plexiglas nach rechts herausziehen um Ihr Poster/Foto auszutauschen.
  • Seite 11 Drag the perspex protection sheet out and insert your own individual poster. Put the short wooden bar back again into the original position. Ziehen Sie die Plexiglasplatte heraus und fügen Sie ihr individuelles Poster ein. Bringen Sie den Balken wieder in die ursprüngliche Position zurück.
  • Seite 12 Enjoy your Enjoy your 60,6 cm = 23,86 inch IvyDesign folding tab- IvyDesign folding tab- 48 cm = 18,9 inch le Model Standard le Model Standard Viel Freude mit Viel Freude mit deinem IvyDesign deinem IvyDesign Klapptisch Model Klapptisch Model...