Plantronics HL10 Benutzerhinweise Seite 4

UK
DIAGRAM KEY
1 Adhesive Mounting Tape
2 Power Cable
3 Accessory Port
4 Lifter Height Switch
For Siemens Optiset, DT Octophon, Alcatel Reflex and Nortel
Meridian series telephones, please refer to Pages 2 and 3 for
additional installation information.
IMPORTANT SAFETY INFORMATION
Please read the following instructions before use:
• The purpose of the HL10 handset lifter is to lift and lower a
telephone handset in conjunction with a compatible Plantronics
amplifier. It should not be used for any other purpose.
• To ensure safe operation, install, adjust and operate the HL10
handset lifter according to these instructions.
• Do not operate or locate this product in a damp environment.
• Keep fingers and other objects clear of the lifting pad.
• Locate the telephone and handset lifter in an area where normal
operation will not be impeded. Only the telephone handset should
rest on the lifter. Any additional weight may prevent it from working.
• Do not open the case of the HL10. It requires no maintenance and
contains no user serviceable parts. The HL10 handset lifter has a
2-year warranty. For details contact your supplier.
• Before cleaning the HL10 handset lifter, disconnect the AC power
adapter and remove the amplifier from the telephone. Use a damp
cloth for cleaning. Do not use liquid or aerosol cleaners. Ensure the
product is dry before reconnecting.
• For year of manufacture please refer to the HL10 date label.
• The equivalent continuous sound pressure level produced by the
HL10 handset lifter is less than 70dB(A) measured at 1m from
the case.
6
5 Lifting Pad
6 Telephone Hookswitch
7 Motor Housing
HL10 TELEPHONE HANDSET LIFTER
The HL10 telephone handset lifter is designed to lift and lower the
handset of a telephone in conjunction with compatible Plantronics
corded and cordless amplifiers. When activated it automatically lifts
most standard telephone handsets off the hookswitch.
INSTALLATION OF THE HL10 WITH THE A20/A22 AMPLIFIER
1. Remove the handset lifter from the packaging and identify the
components as detailed in the diagrams A-D on Page 2.
2. IMPORTANT – Do not remove the backing from the adhesive
mounting tape until directed to do so.
3. Remove the accessory deck cover from the A20/A22 amplifier and
then disconnect the power cable from the AC adapter port. Plug the
power cable of the handset lifter into the accessory port on the
amplifier and turn the jack plug to the left so that it lies flat. Then
reconnect the power supply and replace the accessory deck cover,
ensuring that all the cables are neatly arranged. NOTE – if using an
On-line Indicator in conjunction with your amplifier this must be
disconnected from the amplifier and plugged into the accessory port
on the handset lifter.
4. Position the HL10 under the telephone handset close to the
hookswitch and remove a small section of the backing from the
adhesive mounting tape to temporarily position the lifter. It is not
necessary to secure the lifter using all 3 sections of tape – select the
one most suitable for your telephone.
5. When the lifter is in position you can test its operation by pressing
the headset/handset button on your amplifier. This will activate the
lifter and raise the handset. You will now hear a dial tone in your
headset. The On-line Indicator, if fitted, will also flash.
6. The lifter height switch has three positions - low, medium and high.
Choose the lowest setting which allows the lifter to raise the handset
clear of the hookswitch. After selecting the height, press the
headset/handset button several times to ensure correct alignment of
the handset lifter and free movement of the handset.
7. Once you have determined the appropriate position of the lifter,
remove the remaining backing from the adhesive mounting tape
and press the lifter firmly into place.
UK
7