Behringer X32 Kurzanleitung Seite 11

20
X32 RACK DIGITAL MIXER
X32 RACK DIGITAL MIXER Getting started
Step 3: Getting
(EN)
started
Linux/OS X applications and Windows-based Tip: The X32 RACK remote communication is OSC-
applications for X32 RACK based (open sound control) and we will share the
protocol on our website, allowing developers to
Also offered is a separate remote editor running
design their own control software. Stay tuned to
on host computers that will allow for complete editing
behringer.com for details on the OSC protocol.
control of the X32 RACK via Ethernet. Details of the
remote editor's download, setup and operation are
included in a separate user manual available for
download from the X32 RACK product page. Check out
behringer.com for more information.
01
Ch01 OpeningScene A: S16
02: next 0:00 - 0:00
B: -
con g
home gate dyn eq
FatSn are
Main Display Area Customizing the X32 RACK through the
Utilities page
The top section of the main display permanently
covers useful status information. The top left corner Press the Utility button, located to the right of
shows the selected channel number, its nickname the main display, to bring up useful functions in a
and the selected icon. The next block shows the "context-sensitive" manner. For example:
current scene number and name in amber, as well
• When you are adjusting the equalizer of a
as the next upcoming scene. The center section
console channel, pressing the Utility button
displays the playback file name along with elapsed
will offer copying, pasting, loading or saving of
and remaining time and a recorder status icon.
equalizer settings
The next block to the right has 4 segments to show
• On the Routing pages, pressing the Utility button
the status of AES50 ports A and B, the Card slot and
will offer loading or saving different presets of
the audio clock synchronization source and sample
routing scenarios
rate (top right). Small green square indicators show
proper connectivity. The right most block shows the • In the Scenes menu, pressing the Utility button offers
console time that can be set under Setup/Config. copying, loading, saving or naming console scenes
When working with any given screen, press the NOTE: The X32 RACK DCA groups can be selected
Page keys located on the display bezel to switch to using the Channel Select control in order to adjust
different screen pages. their fader level, mute or solo status. Note, however,
that the main display will remain focused on the last
Editing parameters or settings on each of the screens
real channel (bus or input) that was selected before
is done using the 6 associated push-encoders along
DCA, since DCAs do not feature any processing.
the bottom edge of the display.
Startup and Shutdown, and Update:
• Whenever there is a continuous control or list
entry, you can turn the corresponding knob We recommend switching the X32 RACK mixer on
for editing, which is indicated by various first, and shutting it off last when any sound system
circular icons is connected. This will prevent the possibility of any
unexpected noises being transmitted during the
• When there is a switch or toggle function
startup/shutdown process.
on one of these knobs, you will see a broad
rectangular button along the lower edge of the
The Setup screen's general preference page contains a
field. Pressing the encoder changes the on/off
Safe Main Levels function. When activated, the console
state of the corresponding function. When the
automatically mutes the main LRC levels when booting
rectangular button in the display is dark grey,
the console. It also prevents any scene loading from
the corresponding function is off/inactive; when it
affecting (i.e. turning up) the mains levels.
is amber, the function is on/active
Synchronization and Sample Rate settings for the
console can be adjusted on the Setup/Config page,
but please note that sample rate changes will
require a reboot of the console. When you see a red
X-USB expansion card
The X-USB card allows transmission of up to
32 channels to and from a connected computer.
Please download the X-USB drivers and Quick Start
Guide from behringer.com before connecting the
mixer to your computer. The card is CoreAudio
compatible, allowing it to work with computers with
the OS X operating system software of Apple, Inc.
without a driver.
square indication at the top section of the main
15:33
A: 48K display, please verify if the synchronization settings
: 15
C: X-USB
on Setup/Config make sense.
sends main
16 A 48K
C X-USB
In order to prevent any errors by losing power
during a store operation, we recommend
using the "Safe Shutdown" function from the
Setup/Global page.
NOTE: The X32 RACK can be locked against unintended
use by activating 'Lock Console' from the Setup/Global
page. In this state the UI will not allow any changes
to be made and the display shows "X". Keep HOME
depressed for about 5 seconds to unlock the X32 again.
The X32 firmware can easily be updated by
performing the following steps:
• Download the new console firmware from the
X32 RACK product page onto the root level of a
USB thumb drive
• Plug the USB thumb drive into the front panel USB
connector while the console is turned off
• Hold the USB button depressed while switching
the console on. While booting, the X32 RACK
will run a fully automatic firmware update,
which will take 2-3 minutes longer than the
regular boot sequence
When no update file is available on the USB drive,
or when it is corrupted, the update mode will remain
active, preventing the X32 from booting regularly.
Switch the console off and back on without holding
the USB button to boot the console with the
existing firmware.
CAUTION: Please do not block the vent openings on
the sides of the X32 RACK cabinet! Specifically when
mounting the X32 RACK in a road case, please ensure
there is sufficient space to allow for some airflow.
21
Quick Start Guide
X32 RACK DIGITAL MIXER Puesta en marcha
Paso 3: Puesta en
(ES)
marcha
Ch01 01
01:
home
analog out
Channel Processing Block Patch
Inputs 1-8 Inputs 9-16
Local In 1-8 Local In 1-8
Local In 9-16 Local In 9-16
[Local In 17-24] [Local In 17-24]
[Local In 25-32] [Local In 25-32]
AES50 A1-8 AES50 A1-8
AES50 A9-16 AES50 A9-16
AES50 A17-24 AES50 A17-24
AES50 A25-32 AES50 A25-32
AES50 A33-40 AES50 A33-40
AES50 A41-48 AES50 A41-48
AES50 B1-8 AES50 B1-8
AES50 B9-16 AES50 B9-16
AES50 B17-24 AES50 B17-24
AES50 A25-32 AES50 A25-32
15
Ruteo de E/S
La consola X32 RACK dispone de 16 entradas
analógicas XLR con previo de micro en el panel
trasero, así como 8 salidas XLR y 6 envíos y retornos
auxiliares TRS en el panel trasero. Además,
dispone de dos puertos AES50 , cada uno de ellos con
48 canales de entrada y salida y una ranura de tarjeta
Ch01 01
01:
analog out
home
Edit Output Assignment
Analog Output Current Setting
Output 01 MixBus
Output 02
Output 03
Output 04
Output 05
Output 06
Output 07
Output 08
*Output 09
*Output 10
*Output 11
*Output 12
*Output 13
*Output 14
Select
A: S16 A: 48K 13:45
: 19
0:00 - 0:00 B: - C: X-USB
aux out p16 out card out aes50-a aes50-b
Connected Devices
Inputs 17-24 Inputs 25-32 Aux In 1-4
AES50 A
Local In 1-8 Local In 1-8 Aux 1-4
Local In 9-16 Local In 9-16 Local 1-4
[Local In 17-24] [Local In 17-24] AES50 A1-4
[Local In 25-32] [Local In 25-32] AES50 B1-4
AES50 A1-8 AES50 A1-8 Card 1-4
AES50 A9-16 AES50 A9-16
AES50 A17-24 AES50 A17-24
AES50 A25-32 AES50 A25-32 AES50 B
AES50 A33-40 AES50 A33-40
AES50 A41-48 AES50 A41-48
AES50 B1-8 AES50 B1-8
AES50 B9-16 AES50 B9-16
AES50 B17-24 AES50 B17-24
AES50 A25-32 AES50 A25-32
para 32 canales más de entrada y salida a y desde un
ordenador conectado vía USB.
Las señales de entrada pueden ser pasadas a los núcleos
de procesado audio internos de la consola en bloques
de 8 señales desde cualquiera de las fuentes de entrada
mencionadas antes.
14:09
A: S16 A: 48K
: 37
0:00 - 0:00 B: - C: X-USB
aux out p16 out card out aes50-a aes50-b
Category Processed Output Signal Tap
OFF OFF Pre EQ 0.3 ft
Main (LRC) Main L Post EQ
0.10 m
Mix Bus Main R Pre Fader
0.3 ms
Matrix Main C/M Post Fader
Direct Out Main Bus 01
Monitor Main Bus 02
Main Bus 03
Delay
Main Bus 04
Main Bus 05
Main Bus 06
Main Bus 07
Main Bus 08
Delay
Main Bus 09
Delay
Select Select Select
0.3 ms
Assign Set Delay
Nota: Todos los bloques de señal derivados al
procesado audio será conectados automáticamente a
los canales de entrada correspondientes.
Las entradas locales 17-24 y 25-32 vienen marcadas entre
corchetes para hacerle saber que no están disponibles
físicamente en este dispositivo. Su asignación
obviamente no llevará ninguna señal, pero podrá seguir
usándolas cuando esté preparando shows para una
consola X32 completa.
Cableado para todas las conexiones AES50 entre el
X32 y unidades de escenario S16:
• Cable CAT-5e blindado, Cable Ethercon
terminado en los extremos (recomendado)
• Longitud máxima de cable 100 metros
Las señales de salida pueden ser asignadas
libremente desde cualquier señal interna a
cualquiera de las salidas siguientes:
• 8 salidas analógicas XLR locales (con retardo
digital ajustable para el alineamiento en el
tiempo de los altavoces)
• 8 salidas virtuales (marcadas con un *) para su
ruteo a través de salidas AES50 o de tarjeta
• 6 envíos auxiliares en salidas TRS de 6,3 mm
• 16 salidas de monitorización personal usando el
conector de salida de bus P-16 de la consola
Cualquiera o todas las señales anteriores también
pueden ser reflejadas en bloques de 8 señales en
cualquiera de los
• 48x canales en el puerto AES50 A
• 48x canales en el puerto AES50 B
• 32x canales en la tarjeta de interconexión USB