Blaupunkt KP-R1 Bedienungsanleitung Seite 2
Funk-bedienteil
Inhaltsverzeichnis
Verfügbare Sprachen
Verfügbare Sprachen
"＊" + "8"
"＊" + "9"
"＊" + "0"
"Disarm" twice
A
A
r
r
m
m
/
/
H
H
o
o
m
m
If Remote Keypad is set to "Arm with Use PIN code" ("＊" + "9"
under Test Mode)
Away Arm
Home Arm
Disarm
If Remote Keypad is set to "Arm without Use PIN code" ("＊" + "8"
under Test Mode)
Away Arm
Home Arm
Disarm
If Remote Keypad is set to "Arm with Keypad PIN code" ("＊" +
"0" under Test Mode)
Away Arm
Home Arm
Disarm
C
h
e
c
k
i
n
g
C
h
e
c
k
i
n
g
Press the Status key to inquire Control Panel status, the Status
LED will light up according to Control Panel mode
Red LED On
Red LED Flash
Blue LED on
D
D
u
u
a
a
l
l
K
K
e
e
y
y
Dual Key Alarm function will activate alarm when both keys are
pressed at the same time. To use the functions, please enable
them under Test Mode. (Default are disabled)
"1" + "3"
"4" + "6"
"7" + "9"
L
E
D
I
n
d
i
c
L
E
D
I
n
d
i
c
A
A
c
c
t
t
i
i
v
v
e
e
The Active LED light up whenever any key is pressed.
Off
Blue LED On
Blue LED Flash
Orange LED On
Orange LED Flash Keypad in Test Mode and under Low
S
S
t
t
a
a
t
t
u
u
s
s
The Status LED light up during operation or when the "Status" key
is pressed to inquire Control Panel status
Red LED On
Red LED Flash
Blue LED On
Blue LED Flash
Downloaded from
www.Manualslib.com
1. Enter old code + "Status" Key
2. Enter new 4-digit code + "#" key
Enable Arming without Use PIN code
function
Enable Arm with User PIN code function
(Default)
Enable Arming with KP PIN code
function
To leave Test Mode
e
e
/
/
D
D
i
i
s
s
a
a
r
r
m
m
Enter a Control Panel User PIN Code +
"Arm" Key
Enter a Control Panel User PIN Code +
"Home" Key
Enter a Control Panel User PIN Code +
"Disarm" Key
Press "Arm" Key
Press "Home" Key
Enter a Control Panel User PIN Code +
"Disarm" Key
Enter Keypad PIN Code + "Arm" Key
Enter Keypad PIN Code + "Home" Key
Enter Keypad PIN Code + "Disarm" Key
C
o
n
t
r
o
l
P
a
n
e
l
S
t
a
t
u
s
C
o
n
t
r
o
l
P
a
n
e
l
S
t
a
t
u
s
Away Arm mode
Home Arm mode
Disarm mode
A
A
l
l
a
a
r
r
m
m
F
F
u
u
n
n
c
c
t
t
i
i
o
o
n
n
Panic Alarm
Fire Alarm
Emergency Alarm
a
t
o
r
s
a
t
o
r
s
L
L
E
E
D
D
Keypad in Standby Mode
Keypad in Normal Operation
Keypad in Normal Operation and under
Low Battery
Keypad in Test Mode
Battery
L
L
E
E
D
D
Away Arm mode
Home Arm mode
Disarm mode
No reply from Control Panel
Incorrect PIN code
Request for Home arm when under Away
arm mode
Request for Force Arm
manuals search engine
F
F
a
a
u
u
l
l
t
t
L
L
E
E
D
D
The Fault LED light up whenever faults are detected in the alarm
system.
Orange LED On
Alarm in memory
Orange LED Off
Fault exists in system
B
a
t
t
e
r
y
B
a
t
t
e
r
y
The Remote Keypad uses one 3V lithium battery as its power
source. It also features low battery detection function to notify the
Control Panel when battery voltage is low.
When the Remote Keypad is on low battery, follow the procedure
below to change the batteries.
1. Open the back cover.
2. Remove the old batteries.
3. Press any key several times to fully discharge.
4. Insert the new batteries observing correct polarity.
5. Replace the back cover.
F
F
a
a
c
c
t
t
o
o
r
r
y
y
R
R
e
e
s
s
e
e
t
t
If you forget your Keypad PIN code, or the Remote Keypad has
any problem, you can reset the Remote Keypad to factory
default.
1. Open the back cover.
2. Open the back cover and remove the battery.
3. Press and hold "3" key and insert battery.
4. The Remote Keypad will sound 3 short beeps.
5. Release "3" key, the reset process is now complete
S
S
p
p
e
e
c
c
i
i
f
f
i
i
c
c
a
a
E
E
n
n
v
v
i
i
r
r
o
o
n
n
m
m
e
e
n
n
t
t
a
a
l
l
C
C
o
o
n
n
d
d
i
i
t
t
i
i
o
o
n
n
-10°C to 40°C, relative humidity 85% non-condensing.
R
R
a
a
d
d
i
i
o
o
868 MHz
NOTE: This device works with a genuine Rolling
Code encryption. Please only use it with a
control panel with Rolling Code, otherwise
won't be possible to pair the device.
t
t
i
i
o
o
n
n
- Quicklinks:
- Funk-Bedienteil (Kp-R1)
- Installation
Quicklinks ausblenden:
Inhaltsverzeichnis
