Ufesa BV4625 Gebrauchsanleitung Seite 8

Do the same to attach the other rod. Before switching the hand
mixer on, make sure that the rods are fitted correctly.
The whisks can be inserted into either hole.
However the dough hooks have specific holes. The dough hook
with the washer fitted to the shank must be inserted into the
widest hole on the food mixer. (Figure 2)
Mixer foot:
Open the safety cover (10) located at the back of the hand mixer.
(Figure 3) Insert the mixer foot (6) into its housing, lining up the
guide arrows. (Figure 4)
Turn the mixer foot (6) clockwise until you notice it stop. (1/4 turn)
(Figure 5)
The blade on the mixer foot is protected by a small plastic cover.
Make sure to remove this before attempting to use the mixer foot.
The edge of the blade is very sharp, so be careful not to injure
yourself.
As a safety measure make sure to remove the whisks or dough
hooks before inserting the mixer foot.
USING THE HAND MIXER ON THE SUPPORT WITH
ROTATING BOWL Model BV-4630
Fitting the motor housing to the support:
Rest the front of the hand mixer into its housing on the support
(11). (Figure 6)
Press down on the hand mixer so that it locks in correctly. (Figure
7)
Check that the hand mixer has been fitted correctly.
Fitting the food bowl onto the support:
Press the support retaining clip (12) allowing the support to swing
up. (Figure 8)
Place the food bowl (17) onto the support (11).
Swing the top of the support down onto the bowl so that it slots
on correctly. (Figure 9)
Check that the bowl is slotted onto the base correctly.
Whisks and dough hooks:
To insert the whisks (8) or dough hooks (9), first swing the support
(11) back up by pressing the support retaining clip (12).
Insert the shank into the rod holes, turning it slightly so that it locks
into position. (Figure 10)
Do the same for the other rod and then make sure that the rods
are fitted correctly.
The whisks can be inserted into either hole.
However the dough hooks have specific holes. The dough hook
with the washer fitted to the shank must be inserted into the
widest hole on the food mixer. (Figure 11)
Swing the top of the support down onto the bowl so that it slots
on correctly. (Figure 12)
ATTENTION: Make sure that the hand mixer is unplugged and
the speed switch is set to "0" before fitting the whisks or the
dough hooks.
BV4625/30.indd 8
USE
Whisks and dough hooks:
Once the rods have been fitted correctly, plug the hand mixer into
the electric socket and select a suitable speed, based on what
you intend to mix.
To prevent splashing, insert the whisks (8) or dough hooks (9) into
the food before you switch the mixer on.
Place the rods into the centre of the food that you wish to mix.
Select a suitable speed for work you intend to do.
Move the rods about constantly to ensure an even mix.
When mixing dough, it is best to start off with the liquid ingre-
dients, adding solids gradually to obtain an even mix.
To release the rods, set the speed selector to the "0" position,
unplug the appliance from the wall socket and press the whisk
release button (2), (Figure 13).
Working with the support with rotating bowl: Model
BV-4630
With the rods inserted correctly into the hand mixer, mounted on
the support with the bowl, proceed in the same way as using the
hand mixer manually.
To release the rods when using the support, set the speed
selector to "0" and unplug the appliance from the mains. To re-
lease the rods, first swing the support (11) up by pressing the
support retaining clip (12).
Press the whisk release button (2) .
To take the hand mixer (1) off the support (11), press the hand
mixer release clip (14) and lift the mixer upward (Figure 14)
Mixer foot:
Once the mixer foot has been fitted correctly, plug the hand mixer
into the electric socket.
The mixer foot can only be used at maximum speed, set the
speed selector "4" to any position other than "0" and activate the
function using the turbo speed button "5".
The speed selector function "4" is not operative when the mixer
foot is attached to the blender
Always place the mixing jug on a flat, stable surface.
Keep a firm grip on both the mixer and the jug during use. (Figure
15)
To prevent splashing, insert the mixer foot into the food before
you switch it on.
Move the mixer foot about constantly to ensure an even blend.
The edge of the blade is very sharp, so be careful not to injure
yourself.
As a safety measure make sure to remove the whisks or dough
hooks before inserting the mixer foot.
ATTENTION: When finished, set the speed selector to the "0"
position, unplug the appliance from the wall socket and take
the mixer foot off the motor housing so it can be cleaned.
Make sure to close the protective cover "10" before attempting
to fit the whisks or dough hooks. Once you have done this the
speed selector "4" will be operative again.
8/2/07 09:06:13