AMT 2006 CHEVY CAMARO CONCEPT Handbuch

9
6
C
4
86
10
2
P
87
P
8
P
88
P 23
C
C
16 14 P
13
18
C
19
21
P
10
C
17
11
19
P 12
9 P
20
14 C
C
15 C
11
27 P
C
31
Red
P
28
C
Red 32
P
29
24
30 P
or 9
8
C
Red 33
34 Red
12
C
3
5 C
25
26
4
1
9
5B
P
89
22 P
9 9
7 P 13
P
36
10
C
9
11
6
7
other side is
9
5B
9
7
9
5A
12
5
35
P
37
2006 CHEVY CAMARO
2006 CHEVY CAMARO
CONCEPT
CONCEPT
A631-200
IMPORTANT-Assembly: Carefully study and understand the entire
9
5A instruction sheet. Compare the parts in the box to the instruction
sheet to be sure you have received all the parts required. Carefully
remove parts from trees. Before cementing, "TEST FIT" parts together
to insure proper location and alignment. Scrape paint and plating
from surfaces to be cemented. Subassemblies and components
should be painted before any parts are attached. Use only cement and
paint made for styrene plastic. Painting: Wash parts thoroughly with
mild soap and water. Parting lines, glue joints, and sharp edges
should be sanded or filled with filler putty designed for plastic. Apply
a "primer" coat and allow to dry. Check parts for imperfections and
repeat the procedure if necessary. Remove any lint or dust.
Apply paint evenly, in several thin coats rather than one heavy
coat. Allow each coat to thoroughly dry before the next is applied.
Each coat should be carefully "wet sanded" using slightly damp No.
1200 sandpaper. Be careful not to remove any detail white sanding.
Lightest colors should be painted first. Use frosted tape to mask off
areas not to be painted. Remove tape after paint is dry to the touch.
Use a very fine brush to touch up edges. Decals: See back of decal
sheet for proper application. Decals should to be added after applying
a gloss coat. Apply a final clear coat after decals are dry.
DECAL APPLICATION INSTRUCTIONS
1. Cut decals apart close to image. Apply one at a time.
2. Dip decal into tepid water until paper backing loosens.
3. Moisten area of model where decal is to be applied, to
aid in positioning.
4. Slide decal partly off of paper backing.
5. Place decal on model face up and slide paper
backing away.
Decal
6. Thoroughly blot out excess water, air bubbles, and any
excess emulsion with soft, lint-free cloth.
7. Allow time to dry before handling.
Paper Backing
NOTE: If air bubbles or wrinkles form on an irregular or curved surface, cut decal and press into place.
Round 2, LLC International Hobbycraft (UK) Ltd.
4073 Meghan Beeler Court 21 St. Thomas Street
South Bend, IN 46628 Bristol BS1 6JS England
GENERAL MOTORS Trademarks used under license to Round 2, LLC. AMT is a registered trademark of
Learning Curve Brands, Inc. used under license to Round 2, LLC. ©2011 Learning Curve Brands, Inc. All
rights reserved. ©2011 Round 2, LLC, South Bend, IN 46628 USA. Product and packaging designed in
the USA. Made in China. All rights reserved.
1/25 SCALE MODEL
SYMBOLS
1
• Paint this color
7
• Part number
P
• Plated part
• Another Side
• Part will locate here
• Clear part
• Do not cement
13
• Completed assembly
2X
• Repeat several times
27
• Apply decal
PAINT COLORS
A Black
B Sky Blue
C Aluminum
D
Steel
E Gold
F
White
G Flat Black
H
Orange
J GREEN
K Chrome Silver
L Yellow
M Red
Semi-Gloss
Gloss