Farfisa TD6100MAS Bedienungsanleitung Seite 11

PROGRAMMING
To program you must:
Move the jumper J1 on the back of the
push- button panel from 1-2 to 2-3
position; the display
"Programming / type: ".
Dial the requested programming code
(see table 1) and press
Make the required programming.
At the end of each programming phase,
move the jumper J1 back to 1-2.
Positions of jumper J1
1-2 = operation mode
2-3 = programming mode
Table 1.
Programming codes
00 Entry of passwords for door lock
release (0÷15)
01 Entry-modification-erasing of
names in the electronic index
02 Language selection
03 System programming
04 Entry of text to be shown on the
display
05 Loading names from PC
06 Alphabetical ordering of names
10 Door lock activation time
11 Address of push-button P1
12 Choice the calling tone
16 Entry of passwords for door lock
release (16÷31)
32 Entry of passwords for door lock
release (32÷47)
48 Entry of passwords for door lock
release (48÷63)
64 Entry of passwords for door lock
release (64÷79)
90 Default settings
91 Erase all passwords
92 Erase all user names
Entry of passwords for door lock
release (code 00-16-32-48-64)
Enter the programming mode and insert
code 00 to access the "entry of pass-
words for door lock release" mode; the
display shows "PASSWORD 0 / ".
Dial the first password on the key-
pad, for example 7890; the display
shows "PASSWORD 0 / 7890".
shows Press
"PASSWORD 1 /
Dial the second password on the
keypad, for example 1234; the
to confirm.
display shows "PASSWORD 1 /
1234".
Press
"PASSWORD 2 /
Repeat the operations to insert max.
16 passwords; when you press the
button
password (PASSWORD 15) the dis-
play shows "Programming / type: ".
If you need additional passwords
follow the same procedure by re-
placing the 00 code with the codes
16, 32, 48 or 64. The display will
show in sequence the number of
passwords (16, 17, ....; 32, 33.... etc.)
in conjunction with code the drive
the lock.
Continue by entering the code of a
new programming or exit by moving
the jumper J1 back 1-2.
Modifying passwords
To change the previously saved
passwords you must enter the
programming mode and then:
select the programming code 00/16/
32/48/64;
press the button
word you want to modify is displayed;
press to go to the password you
want to modify;
enter the new password on the key-
board and then press the button
repeat the operation for all the pass-
words you want to modify;
move the jumper J1 from 2-3 to 1-2
to exit the programming mode.
Deleting a code
To delete the previously saved
passwords you must enter the
programming mode and then:
select the programming code 00/16/
32/48/64;
press the button
word you want to delete is displayed;
press the button
repeat the operation for all the pass-
words you want to modify;
move the jumper J1 from 2-3 to 1-2
to exit the programming mode.
; the display shows
".
; the display shows
".
to confirm the sixteenth
until the pass-
until the pass-
and then ;
Entry / modification / deletion of
names (code 01)
The digital keyboard TD6100MAS has
an alphanumerical display with 32
characters that displays the user name
and extension number (28 characters
are used for user name and the last 4
characters on bottom right are used for
extension number). To save them, you
must follow the procedure illustrated
below. The name must be entered
starting from the first character on top
left and the last digit of the extension
number must be entered in the last
position on bottom right, otherwise the
number will not be saved (see "deletion
of names").
After you have entered all the names,
the system will automatically arrange
them in alphabetical order.
Example
YES
NO
Function of buttons when entering
or modifying a name
Hold this button pressed to scroll
the list of existing names
Hold this button pressed to move
forward the cursor to the next char-
acter
Hold this button pressed to scroll
down the list of characters
Hold this button pressed to scroll up
the list of characters
When searching for characters, the
display shows uppercase letters, low-
case letters, numbers, special
characters and space in a sequence.
Entry of names
Move the jumper J1 from 1-2 to 2-3.
Enter the code 01 and press
display shows the first name. The
display is empty if no codes are pro-
grammed.
Press or to select the character
for the first cell; press
second cell; press or
the character for the second cell;
continue until you have entered the
complete name with code. Press
after you have entered the number in
; the
to go to the
to select
11
Mi 2437/1