Technical Features - PRASTEL TCO7RX Handbuch

11. SAVING OF ENERGY (LOW POWER)
By the dip switch Low Power present on the transmitter device it is possible to limit the frequency with which the transmitter device transmits its state
of functioning (period of interrogation): but in this case it will be necessary to keep in consideration the condition of dangerous that can be created if
the power supply (battery) is taken off to the transmitter during the interval of time before the successive transmission of its state and successively the
sensible edge goes on alarm: in this case the receiver will signal the alarm only after the period of interrogation.
With the dip 2 of the transmitter on OFF: energy saving deactivated, check the state of the transmitter each second (low power deactivated)
With the dip 2 of the transmitter on ON: energy saving activated, check state of transmitter each 15 seconds (low power activated)
12. DEVICES TEST
By the dip switch 1 of the receiver it is possible to select if the device test must be carried out with a high logic signal (so the test will activate itself if
between the terminals TEST1 and TESTC will be present a tension from 10V dc to 24 Vdc) or with a low logic signal (so the test will activate itself if
between the terminals TEST1 and TESTC will be present a tension of 0Vdc). In this case, the test will be for the device memorized to the relay 1. The
same is for TEST2 and TESTC for the device memorized to the relay 2.
During this test, the receiver sends a signal to all the associated transmitter with the request of their state. If all the devices answer positively, the test
is passed and the correspondent relay (which was previously open) re – closes itself.
With the dip 1 of the receiver on OFF position: the test of the device is executed by applying a high logic signal 10-24 Vdc at the input.
With the dip of the receiver on ON position: the test of the device is executed by applying a low logic signal 0 Vdc at the input.
Note : in case you don't want to use the test of the device, place the dip 1 on OFF position.

13 TECHNICAL FEATURES

Caratteristiche tecniche
Frequenza
Portata del sistema in campo libero
Alimentazione trasmettitore
Alimentazione ricevitore
Durata batteria
Coste compatibili
Numero di uscite
Numero di costa associabili per
ogni ricevitore
WARNING:
TCO7TX DIP1 OFF: mechanical safety edge (normally closed contact)
This application does not comply with the automatic doors security norm for use EN 12453 because the
connection of the NON-resistive component connected to the transmitter is not checked.
GUARANTEE - In compliance with legislation, the manufacturer's guarantee is valid from the date stamped on the product and is restricted to the
repair or free replacement of the parts accepted by the manufacturer as being defective due to poor quality materials or manufacturing defects. The
guarantee does not cover damage or defects caused by external agents, faulty maintenance, overloading, natural wear and tear, choice of incorrect
product, assembly errors, or any other cause not imputable to the manufacturer. Products that have been misused will not be guaranteed or repaired.
Printed specifications are only indicative. The manufacturer does not accept any responsibility for range reductions or malfunctions caused by
environmental interference. The manufacturer's responsibility for damage caused to persons resulting from accidents of any nature caused by our
defective products, are only those responsibilities that come under European law.
Technical features
Frequency
Range of the system in free space
Transmitter power supply
Receiver power supply
Battery duration
Compatible ribs
Number of output
Number of ribs for receiver
FRA ENG ITA ESP
868,3 Mhz
30 m
2 batterie / battery AA
12/24 Vac-dc
2 anni (modalità funzionamento normale)
5 anni (modalità risparmio energetico)
2 years (normal functionning mode)
5 years (power saved mode)
Meccaniche e/o 8,2K
Mechanical and/or 8,2K
2
4 per ogni uscita.
4 for each output.
DEU POR
ISTCO7KIT_EN_12-17.pdf
6 / 6