Philips Philipshave QT4020 Bedienungsanleitung Seite 2

ENGLISH
Important
.
Read these instructions for use carefully before
using the appliance and save them for future
reference.
◗ Make sure the appliance, the cord and the
powerplug do not get wet.
◗ Check if the voltage indicated on the
powerplug corresponds to the local mains
voltage before you connect the appliance.
◗ Only use the powerplug supplied.
◗ Keep the appliance out of the reach of
children.
◗ Charge, use and store the appliance at a
temperature between 15cC and 35cC.
◗ This appliance is only intented for trimming
the human beard. Do not use it for any other
purpose.
◗ Do not use the appliance when the cutting
unit is damaged or broken, as this may cause
injury.
◗ If the powerplug is damaged, always have it
replaced by one of the original type in order
to avoid a hazard.
◗ The powerplug contains a transformer. Do
not cut off the powerplug to replace it with
another plug, as this will cause a hazardous
situation.
Charging
.
Charge the appliance fully before you start using it
for the first time.
1 Make sure the appliance is switched off
(fig. 1).
2 Insert the appliance plug into the appliance
(fig. 2).
3 Put the powerplug in the wall socket.
◗ The green light on the powerplug will go on
to indicate that the appliance is charging
(fig. 3).
It will take approx. 10 hours to fully charge the
battery.
Do not charge the appliance for more than 24
hours.
A fully charged appliance has a cordless trimming
time of up to 35 minutes.
◗ The appliance does not run from the mains.
When the battery is empty, charge it as
described above.
Optimising the lifetime of the battery
When the appliance has been charged for the first
time, we advise you to use it until the battery is
completely empty.
Do not recharge the appliance in between the
trimming sessions.
Continue using the appliance until the motor
almost stops running during a session. Then
recharge the battery. Follow this procedure at least
twice a year.
Trimming
.
Always comb the beard and/or moustache with a
fine comb before you start trimming.
If you are trimming for the first time, be careful. Do
not move the trimmer too fast. Make smooth
and gentle movements.
Downloaded from www.Manualslib.com manuals search engine
Trimming with comb attachment
1 Turn the Precision Zoom Lock` to the
desired trimming length setting (see table)
(fig. 4).
The setting will appear in the window below the
Precision Zoom Lock`.
If you are trimming for the first time, start by using
B
the maximum trimming length setting (9).
2 Switch the appliance on.
3 To trim in the most effective way, move the
trimmer against the direction of hair growth.
Make sure the surface of the comb always
stays in contact with the skin (fig. 5).
4 If a lot of hair has accumulated in the comb,
remove the comb attachment and blow
and/or shake the hair out of the comb. The
selected trimming length setting will not
change when you do this (fig. 6).
Trimming length settings table
setting resulting beard length
1 1.5 mm
2 2.5 mm
3 4 mm
4 5.5 mm
5 7.5 mm
6 9.5 mm
7 12 mm
8 15 mm
9 18 mm
Trimming with the unique 'stubble look'
setting
◗ Using the minimum setting (1) will result in a
'stubble look' (fig. 7).
Trimming without comb attachment
Full beards and single hairs
1 Remove the comb attachment by pulling it off
the appliance (fig. 8).
Never pull at the flexible top of the comb
attachment. Always pull at the bottom part.
2 Switch the appliance on.
3 Make well-controlled movements. Touch the
hair lightly with the trimmer (fig. 9).
Cleaning
.
Do not use abrasives, scourers or liquids such as
alcohol, petrol or acetone to clean the appliance.
1 Make sure the appliance is switched off and
disconnected from the mains before you start
cleaning it.
2 Remove the comb attachment.
3 Open the cutting unit (fig. 10).
4 Clean the cutting unit and the inside of the
appliance with the brush supplied (fig. 11).
5 Close the cutting unit by pushing it back onto
the appliance until you hear a click (fig. 12).
The appliance does not need any lubrication.
4203 000 31431
2/13