Calypso Watches IKMAD-4A Betriebsanleitung Seite 3

I
ENGLISH INSTRUCTION MANUAL
FEATURES AND SPECIFICATION
SECONDS
(OPTIONAL)
CHIME SIGNAL
AFTERNOON
HOURS
1. Accuracy at normal temperature: not more than 30 seconds a month.
2. Time keeping mode: hours, minutes, seconds, month, date, day of week, "PM" (only
available in 12 hour format).
3. Alarm Mode: daily alarm.
4. Stop watch Mode: Measuring unit: 1/100 of second
measuring capacity: 23:59'59"
5. Normal operating temperature range:10"C-40"C.
6. Battery type: CR2032, CR2016, CR2012, CR1620
HOW TO SET NORMAL TIME/CALENDAR
From the normal time display, press S3 and hold for 3 seconds, the alarm time shows.
Press S3 again to set normal time and calendar.
First - seconds will flash-Press S2 to reset to 00 (if seconds in lhe range of 30 to 59, minutes
will add 1; if seconds in lhe range of 00 to 29, minutes will not be changed.)
1. Press S1 - minutes will flash-advance by pressing S2
2. Press S1 - hours will flash-advance by pressing S2
3. Press S1 - date will flash-advance by pressing S2
4. Press S1 - month will flash-advance by pressing S2
5. Press S1 - day will flash-advance by pressing S2
While advancing, hold S2 can fasten the process. Press S3 at any stage to return to normal
display.
HOW TO USE THE CHRONOGRAPH
From the normal time display, press S3 once to enter chronograph function.
Simple usage:
• Press S1 to start counting
• Press S1 again to stop counting
• Press S2 to reset to zero
• Press S3 to return to normal display (this can be done at any time with the chronograph still
running)
Advanced usage (LAP function):
• Press S1 to start counting
• Press S2 , first time split T1 (0 to T1) shows. The numbers stop flashing, but chronograph is
still counting in fact.
• Press S2 again to continue counting
• Further press S2, the second split time T2 (0 to T2) shows. This operation can be repeated
and the splits time can be read: 0 to T3, 0 to T4 etc.
• Press S1 to stop the time counting of the chronograph.
• Press S2, the last split time Tn (0 to Tn) shows.
• Press S2 again, the chronograph is reseted to zero. Press S3 to return to normal display.
By virtue of the regulations pursuant to the handling of waste products deriving from electronic and electrical equipment, end of lifecycle watch making
products must be selectively collected for processing. You may therefore dispose of your quartz watch making products at any of our retail outlets or any other
authorized collection point. The selective collection, processing, rating and recycling of these products helps contribute to safeguarding the environment and
protecting our health.
DAY OF WEEK
ALARM SIGNAL
MINUTES
IKMAD-4A
HOW TO SET ALARM TIME
You can set alarm with hours and minutes. When the alarm is on, the alarm(BI-BI) sound for
20 seconds when alarm occur. Press S2 to stop the alarm after it starts sound.
From the normal time display, press S3 and hold for 3 seconds, alarm time shows.
Now-hours will flash, Press S2 to advance
Press S1-minutes will flash, Press S2 to advance
While advancing, hold S2 can fasten lhe process. Press S3 to return to normal lime
display.
ALARM & CHIME ON/OFF
From the normal time display, hold S2 and then press S1 to activate or turn off the
alarm and/or chime. When chime is on, the chime signal appears and there is one beep
every hour. When alarm is on, the alarm signal appears and it will sound for 20 seconds at the
present time.
HOW TO DISPLAY MONTH AND DATE
From the normal time display, hold S1 to read the date. Hold S1 and then press S2, the mode
of date display will be change between month/date and date/month format.
HOW TO CHANGE 12/24 HOUR FORMAT
From the normal time display, hold S2 (or S1) and then press S3 to select 12 or 24 hour
format.
HOW TO USE EL BACKLIGHT AND ELECTRIC TORCH
ln any mode press S4 button to illuminate the display for about 3 seconds.
Note:
1. lf the watch is without button S4, this function is not available
2. The backlight of the watch employs an electro-luminescent (EL) light, which tends to lose
illuminating power alter very long use.
3. The illumination provided by backlight may be hard to see when viewed under direct
sunlight.
4. Press button S2 to turn on electric torch under normal time display. When press and hold
button S2, the alarm time will be shown. At the same time, the torch is on. Release to
return to normal time display.
CARE OF YOUR WATCH
1. This watch contains electronic components. Never attempt to open the case or remove the
back cover.
2. Do not operate push buttons below the surface of the water while swimmingor diving.
3. Should water or condensation appear in the water, have the water checked immediately.
Corrosion of electronic parts can occur inside the case.
4. Avoid severe impact. The watch is designed to withstand impact under normal use. It is
inadvisable to subject it to severe impact or rough usage.
5. Avoid exposing the watch to extreme temperature.
6. Clean the watch with soft cloth and clean water only. Avoid using chemicals.
7. Keep your watch away from the conditions of strong electricfield and static electricity.