Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Read this manual carefully before using this product and check whether there are any
damaged parts. The product cannot be installed in case of damages. Keep this manual for
further reference.
SAFETY WARNINGS:
a) Keep this product out of reach of children and unauthorized users.
b)
Before using the device, make sure that all screws have been tightened.
c) This unit can become extremely hot whilst in operation; do not touch until it has had time
to cool down.
d) When the light bulb is burning or not completely cooled down, please do not touch it.
e) Mark sure there is adequate ventilation to aid heat dissipation.
f)
Minimum distance from lighted objects 1 m.
1m
g) For outdoor use.
h)
If the glass is broekn, replace it immediately.
i) If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
j) The lighting direction can not be adjusted to down ward.
EXPLANATION OF SYMBOLS:
Conforms to relevant European requirements for the product.
The crossed-out wheeled bin symbol indicates that the item should be disposed of
separately from household waste. The item should be handed in for recycling in
accordance with local environmental regulations for waste disposal. By separating a
marked item from household waste, you will help reduce the volume of waste sent to
incinerators or land-fills and minimize any potential negative impact on human health
and the environment.
TECHINICAL DATA:
Floodlight with tripod
Type
0208
Rated voltage
220-240 V ~ 50 Hz
Rated power
Max.500 W
IP54
IP Level
R7s 400 W / 118 mm
Lamp
Cable
H05RN-F 3G 1.0mm²
Weight
3.75 kg
Dimension of
177 x 140 x 5 mm
protective glass
CLEANING:
Turn off the power to clean the lamp and let the lamp cool down. Clean the lamp with soft
cloth (if necessary slightly moistened). Never use alcohol or a similar solvent, this could
damage the lamp.
INSTALLATION:
Caution: Before installation, please make sure the plug is not connected to the socket.
1
2
1. Take the tripod base from the packaging and put it in a flat place.
Loose the scres, fully spread off the feet and tighted the scres again. Be sure that the tripod
is stable and the ground is firm.
2. Loosen the screw caps and pull out the tubes to the desired height. Then tighten the clamps.
3. Adjust the angle of the flood light and then tighten the clamp of the flood light on the stand
by tightening the rotary knobs on the flood-lit.
4, The inclination angle of the flood light can be adjusted up and down by means of screws
Note: Do not touch the lamp when it is lit or has
E
MAX 4°
A
MAX 4°
B
C
D
INSTALLATION OF THE BULB:
a) Before installing bulb, please make sure the plug is not connected to the socket.
b) Loose the upper scres from the light guard and open it.
c) Take the bulb our of it's packaging. Do not touch the bulb with bare hand. Use a towel
to fix the bulb into the fitting. First press one side of the fitting against the metal pin and shift
the pin backwa
rds so that you can press the other side of the bulb against the metail pin.
d) After chanding the light bulb, please pay attention to the correct positioning of the seal gasket.
e) Fix the light guard by tightening the screw. Do not over tighten which may damage the glass.
A.
B.
C.
1.
2.
07
3
4
not yet cooled down.
Note: Check after mounting the floodlight is
su
re whether the tripod rests securely and is
on a
stable surface. The cable can be wrapped
round the cable holder.
Note: The halogen bulb in the housing would
blow p
rematurely, if the housing at an angle
about
4° would mounted
A. Medium knob
B. Rotary locks
C. Ankles
D. Cable bracket
E. Flood light housing screw
V200323
I
08
GB
Werbung
