HERKULES BKS 315/230 Bedienungsanleitung Seite 20

Anleitung BKS 315-230_SPK7:Anleitung BKS 315-230_SPK7
GB
together.
Important: It is imperative that the foot with the
opening (19) for the switch/plug block is
mounted correctly on the left front side (see Fig.
1; 2; 6).
Screw the side struts (24) and the legs (18,19)
loosely together.
Fasten the extractor connection to the bottom of
the chip box (17) with 4 screws (32) (Fig. 3).
Mount the four rubber feet (25) on the legs.
Working from the inside, fit the mounting for the
chassis (22) to the rear legs (18) with 4 screws
(33). (Fig. 4)
Turn the saw upside down and place it on the
legs.
Insert the switch/plug block (11) into the opening
in the leg and secure tightly from the side with 2
screws (34) (Fig. 6)
Fit the push handles (16) to the front legs with 2
screws (35) in each case. (Fig. 6)
Caution: The handles (16) must be able to
move freely and must retract independently.
Fit the mounting for the extractor hose (29) to
the rear of the saw table (1) with 2 screws (36).
(Fig. 5)
Then align the base frame and tighten all the
screws.
Attach the 2 thumb screws (21) for the terminal
strip to the front side of the saw table.
Important: Attach the thumb screws only
loosely, as otherwise it will be impossible to
mount the parallel stop (7). Mount the tool hooks
(28) on the side of a front leg. (Fig. 6)
7.2. Assembling the table length extension
Screw the short side of the length extension
table (10) loosely to the rear side of the saw
table (1) with 2 screws.
Now tightly screw the long table supports (47) to
the base frame and the length extension table
using the holes provided.
Align the length extension table with the saw
table (1) so that it is flat and tighten all the
screws.
7.3 Using the chassis (Fig. 8)
To swing the chassis out, gently lift the saw at
the back (a) and push the wheels backwards
(15) (b).
Then lower the saw again, keeping it in this
same position (c).
The saw is now standing on the wheels and can
be transported by one person with the aid of the
handles (16).
Important: After transportation, the chassis (15)
must immediately be retracted in order to ensure
20
that the saw is standing securely.
To do this, return the wheels to their starting
position by following the sequence in reverse.
7.4 Fitting / removing the saw blade guard (Fig. 7)
Mount the saw blade guard (2) on the splitter (5)
so that the screw (33) fits through the hole (45)
in the splitter (5).
Do not tighten the screw (37) too far – the blade
guard must be able to move freely.
Fasten the extractor hose (13) to the extractor
adapter (14) and to the extractor socket of the
blade guard (2).
A suitable extractor system has to be connected
to the outlet of the extractor adapter (14). (Fig. 3)
To remove the saw blade guard, proceed in
reverse order.
Important!
The guard hood (2) must always be lowered
over the workpiece before you begin to cut.
7.5. Setting the splitter (Fig. 7/9/10/11)
Important! Pull out the power plug.
Set the blade (4) to max. cutting depth, move to
0° position and lock in place (see 8.2).
Remove the saw blade guard (see 7.4).
Take out the table insert (6) (see 7.6).
Slacken the nut (38).
7.5.1. Setting for maximum cuts (Fig. 7/9/10/11)
Push up the splitter (5) until the gap between the
saw table (1) and the upper edge of the splitter
(5) is at its maximum.
The maximum distance between the saw blade
(4) and the splitter (5) is 8mm.
Re-tighten the nut (38) and mount the table
insert (6).
7.5.2. Setting for concealed cuts (Fig. 7/9/10/11)
Push down the splitter (5) to the point where the
tip of the splitter is 2 mm below the uppermost
saw tooth tip.
The distance between the splitter (5) and the
saw blade (4) may again be max. 8 mm (see Fig.
10).
Re-tighten the nut (38) and mount the table
insert (6).
Important! After you make a concealed cut,
be sure to refit the saw blade guard.
The setting of the splitter has to be checked
each time after changing the saw blade.
10.07.2008 15:49 Uhr Seite 20