Cleaning Instructions; Accessories; Storage; Battery Transport - RIDGID RBC 10 Bedienungsanleitung

RBC 10 Li-Ion Battery Charger

Cleaning Instructions

WARNING
Unplug charger before cleaning. Do not use any
water or chemicals to clean charger or batteries to
reduce the risk of electrical shock.
Should it be necessary to clean the charger, follow the pro-
cedure detailed below:
1. Unplug the charger.
2. If present, remove battery from charger.
3. Remove any dirt or grease from the exterior of the
charger and battery pack with a cloth or soft, non-
metallic brush.

Accessories

WARNING
The following accessories have been de signed to
function with the RIDGID RBC 10 Li-Ion Battery
Charger. To prevent serious injury, use only the
accessories specifically designed and recommend-
ed for use with the RIDGID RBC 10 Li-Ion Battery
Charger, such as those listed below. Included charg-
er and batteries are not compatible with other mod-
els of RIDGID Li-Ion batteries and chargers.
For a complete listing of RIDGID attachments avail-
able for this charger, see the RIDGID Catalog on line
at www.RIDGID.com or www.RIDGID.eu.
RBC 10 Li-Ion Battery Chargers
Catalog
No. Voltage
32068 120V
32073 230V
34563 230V
33193 230V Australia & Latin America
Li-Ion Battery Packs
Catalog
No. Capacity Region
31013 18V 1.1Ah North & Latin America, Australia
32743 18V 2.2Ah North & Latin America, Australia
31018 18V 3.3Ah North & Latin America, Australia
32473 18V 1.1Ah Europe & China
28218 18V 2.2Ah Europe & China
28448 18V 3.3Ah Europe & China
All listed batteries will work with any model RBC 10 charger. The difference
between batteries for different regions is in label markings.
4
Plug
Region Type
North America A
Europe C
China A
I
No.
Cells*
5
10
15
5
10
15

Storage

WARNING
secured, locked area that is out of reach of children and
people unfamiliar with proper charger operation.
The battery packs and charger should be protected a -
gainst hard impacts, moisture and humidity, dust and
dirt, extreme high and low temperatures, and chemical
solutions and vapors.
NOTICE Long term storage in the fully charged state,
the fully discharged state or in temperatures above 95°F
(35°C) can permanently reduce the capacity of a bat-
tery pack.

Battery Transport

The battery is tested according to UN document
ST/SG/AC.10/11/Rev/3 Part III, subsection 38.3. It has
effective protection against internal overpressure and
short circuiting as well as devices for the prevention of
violent rupture and dangerous reverse current flow.
The lithium-equivalent content in the battery is below
applicable limit values. Therefore, the battery is not sub-
ject to national or international regulations pertaining to
dangerous mediums, neither as an individual compo-
nent nor when inserted into a machine. However, the
regulations governing dangerous goods may be relevant
when transporting several batteries. In this case, it may be
necessary to comply with special conditions (e.g., con-
cerning the packaging).

Service and Repair

Improper service or repair can make the machine
unsafe to operate.
There are no user-serviceable parts for this charger or bat-
tery packs. Do not attempt to open charger or battery
cases, charge individual battery cells, or clean internal
components.
For information on your nearest RIDGID Independent
Service Center or any service or repair questions:
• Contact your local RIDGID distributor.
• Visit www.RIDGID.com or www.RIDGID.eu to find
your local Ridge Tool contact point
• Contact Ridge Tool Technical Services Department at
rtctechservices@emerson.com, or in the U.S. and
Canada call (800) 519-3456
Ridge Tool Company
Store the charger and batteries in a dry,
WARNING