IMER MASONRY 350 Handbuch Für Bedienung, Wartung Und Ersatzteile Seite 9

Dear Customer,
Congratulations on your choice of purchase: IMER saws are the
result of years of experience and is equipped with all the latest
technical innovations.
WORKING IN SAFETY
To work in complete safety, read the following instructions
carefully.
- This OPERATION AND MAINTENANCE manual must be kept on
site by the person in charge, e.g. the SITE FOREMAN, and must
always be available for consultation.
- The manual is to be considered integral part of the machine and
must be kept for future reference (EN 292/2) until the machine is
disposed of. If the manual is damaged or lost, a replacement may
be requested from the saw manufacturer.
- The manual contains important information regarding site
preparation, machine use, maintenance procedures, and requests
for spare parts. Nevertheless, the installer and the operator must
both have adequate experience and knowledge of the machine prior
to use.
- To guarantee complete safety of the operator, safe operation and
long life of equipment, follow the instructions in this manual carefully,
and observe all safety standards currently in force for the prevention
of accidents at work (use of safety footwear and gloves in accordance
with S.I. N°3073 of 30/11/92).
Pay special attention to warnings bearing the following
symbol.
Safety glasses or a protective visor must be worn at
all times.
MAKE SURE THAT SIGNS ARE LEGIBLE.
It is strictly forbidden to carry out any form of
modification to the steel structure or working parts of the
machine.
- IMER INTERNATIONAL declines all responsibility for non-
compliance with laws and standards governing the use of this
equipment, in particular; improper use, defective power supply, lack
of maintenance, unauthorised modifications, and partial or total failure
to observe the instructions contained in this manual.
1. DESIGN STANDARDS
MASONRY 350 saws are designed and manufactured according to
the following standards: I.E.C. 34.4; EN 392 (91/368 CEE); CEI
EN60204.
2. NOISE EMISSION LEVEL
Operator exposure to sound emission levels (continuous sound
pressure levels equal to "A" weighting); the MASONRY 350 saw
noise emission level during cutting is 93 dB(A) with continuous rim
blade.
3. CUTTING SPECIFICATIONS
This saw model has been specially designed by IMER for cutting
stone, ceramics, marble, granite, concrete and similar materials.
Only water-cooled diamond blades with continuous or segmented
edges must be used. Under no circumstances must dry cutting
blades be used or materials other than those specified above. IMER
INTERNATIONAL declines all responsibility for damage caused by
improper use of the above machine.
4. CUTTING CAPACITY
- max. cutting capacity with vertical blade - 120 mm
- max. cutting capacity with blade at 45° - 70 mm
- min. dimensions of workpiece - min. width 50 mm
- max. dimensions of workpiece
Vertical blade lowered:
wxhxl = 500 x 25 x 480
= 500 x 60 x 450
= 500 x 120 x 400
IMER INTERNATIONAL S.p.A.
MASONRY 350
Vertical blade raised , cutting with blade lowered from above:
Blade at 45°:
5. WARNING
- Do not load the saw with workpieces that exceed the specified
weight (max. 40 kg)
- Ensure stability of machine and workpiece before, during or after
cutting. Install supplementary support surfaces at the same height
as the worktable.
- Respect the environment; use suitable receptacles for collection
of cooling water contaminated with cutting dust.
6. SAFETY PRECAUTIONS
IMER saws are designed for work on construction sites and under
conditions of natural light and in workshops under conditions of
natural or artificial lighting of minimum 500 LUX.
subject to risks of explosion and/or underground sites.
- IMER saws may only be used when fitted with all required safety
devices which must be in perfect condition.
- Never use makeshift and/or faulty power cables.
- Make electrical connections on the construction site where they
will not be subject to damage. Never stand the saw on power supply
cables.
- Lay power cables where they are not subject to risk of damage or
contact of connectors with water. Only use connectors fitted with
water-spray protection (IP55).
- Repairs to electrical installations must only be carried out by
qualified technicians. Always ensure that the machine is
disconnected from the power supply and is completely immobile
during repairs and maintenance operations.
earthing plant on the construction site with wire braid of
minimum 16 mm² section. The connection point is
identified by a screw welded to the frame (see Fig.1),
and on the rating plate by the earthing symbol.
7. ELECTRICAL SAFETY
IMER saws comply with EN 60204-1; and are fitted with:
- protection device against automatic re-start after power failure.
- Short-circuit cutout device
- Motor overload cutout switch
8. TRANSPORTATION (Ref. Fig.2)
socket before moving the saw, and lock head support carriage
movement by means of the relative knob (ref. 3). To transport
the machine use slinging equipment with 4 rope legs, fixing
the hooks to the relative attachments.
9. INSTALLATION (Ref. Fig.2)
Fix the hooks to the relative attachments on the machine and lift
the machine out of its package.
- Unlock the legs by sliding out split pins (ref.2) and pins (ref.1).
- Lock the legs at working height. Refit the pins in the leg supports
and insert the split pins.
- Install the machine on a completely even and stable surface.
10. ELECTRICAL CONNECTION
upline residual current circuit breaker with high sensitivity (10
mA). Alternatively, an insulation transformer may be used to
protect against indirect contact by breaking the circuit: in this
case it is important that no part of the transformer's powered
secondary circuit be earthed. Furthermore, the circuit should
be fitted with an insulation monitor to signal faults of this natu-
re in the machinery.
Ensure that the mains voltage corresponds to that specified for the
9
wxhxl = 500 x 120 x 450
wxhxl = 500 x 30 x 480
The machine must never be used in environments
- Connect the machine to a suitable equipotential
- Stop the saw only by means of the main switch.
- The symbol shown on the label (see left) indicates
the warning "ENSURE ALL PROTECTION DEVICES
ARE INSTALLED AND IN PERFECT CONDITION
BEFORE SWITCHING ON THE MACHINE"
WARNING! Always remove the plug from the power
The power line must be equipped with a fast-acting,