Troubleshooting Information; Specifications - Tektronix TDS3CHG Betriebsanleitung

Troubleshooting Information

If the TDS3CHG does not charge the battery pack,
try these steps before returning the battery pack or
the charger for service:
S
Verify that the green light on the charger is on
when you apply AC power to the TDS3CHG.
S
Using the 10 A range, connect a DMM across
the output terminals of the TDS3CHG. Verify
that the yellow light turns on and that the cur-
rent reading is 1.2 A or greater.
S
Store the battery pack at room temperature for
several hours and then try to charge it again.

Specifications

Input 100 - - 250 VAC, 50/60 Hz, CAT II
Output 30 W, 18 VDC, 1.8 A (current limited)
- - 10 °C to +45 °C
Operating
Temperature
Certifications and Compliances
EC Declaration of Conformity - - EMC
Meets intent of Directive 89/336/EEC for Electromagnetic
Compatibility. Compliance was demonstrated to the
following specifications as listed in the Official Journal of
the European Union:
EN 50081-1 Emissions:
EN 55077 Class A Radiated and Conducted
EN 60555-2 AC Power Line Harmonic
EN 50082-1 Immunity:
IEC 801-2 Electrostatic Discharge
IEC 801-3 RF Electromagnetic Field
IEC 801-4 Electrical Fast Transient/Burst
IEC 801-5 Power Line Surge
Australia/New Zealand Declaration of Conformity - - EMC
Complies with EMC provision of Radiocommunications Act
per the following standard(s):
AS/NZS 2064.1/2 Industrial, Scientific, and Medical
Equipment: 1992
FCC Compliance Emissions comply with FCC Code of
- - EMC Federal Regulations 47, Part 15,
Subpart B, Class A Limits.
www.tektronix.com
EC Declaration of Conformity - - Low Voltage
Compliance was demonstrated to the following
specifications as listed in the Official Journal of the
European Union:
Low Voltage Directive 73/23/EEC, amended by 93/69/EEC
EN60950, Third Safety of information technology
Edition equipment, including electrical
business equipment
U.S. Nationally UL1950, Third Edition
Recognized Safety of information technology
Testing equipment, including electrical
Laboratory Listing business equipment
Canadian CAN/CSA C22.2 No. 950
Certification Safety of information technology
equipment, including electrical
business equipment
Additional Japan Dentori (T mark)
Compliance
EN60950
ANSI/ISA S82.01:1994
Safety standard for electrical and
electronic test, measuring, controlling,
and related equipment.
IEC61010-1
Safety requirements for electrical
equipment for measurement, control,
and laboratory use.
Installation (Overvoltage) Category
Terminals on this product may have different installation
(overvoltage) category designations. The installation
categories are:
CAT II Local-level mains (wall sockets).
Equipment at this level includes
appliances, portable tools, and similar
products. Equipment is usually
cord-connected.
CAT I Secondary (signal level) or battery
operated circuits of electronic
equipment.
Pollution Degree 2: Typical home or office environment.
WARRANTY SUMMARY
Tektronix warrants that the products that it
manufactures and sells will be free from defects in
materials and workmanship for a period of one (1)
year from the date of shipment from an authorized
Tektronix distributor. If a product or CRT proves
defective within the respective period, Tektronix
will provide repair or replacement as described in
the complete warranty statement.
To arrange for service or obtain a copy of the
complete warranty statement, please contact your
nearest Tektronix sales and service office.
EXCEPT AS PROVIDED IN THIS SUMMARY
OR THE APPLICABLE WARRANTY
STATEMENT, TEKTRONIX MAKES NO
WARRANTY OF ANY KIND, EXPRESS OR
IMPLIED, INCLUDING WITHOUT
LIMITATION THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE. IN NO EVENT
SHALL TEKTRONIX BE LIABLE FOR
INDIRECT, SPECIAL OR CONSEQUENTIAL
DAMAGES.
Copyright  Tektronix, Inc.
Beaverton, OR 97077