Technical Specifications - TECNA 9200 Bedienungsanleitung

Install the balancer before using it. This operation is to be carried out by skilled personnel who must comply with the
directions outlined in this manual: a wrong installation could cause injury/damage to people/property.
This manual contains important information that the user must adhere to in order to use the balancer safely. Be sure
to have clearly understood all the instructions before using the balancer. Failure to do so could cause injury.
The balancer was built in conformity with European Community Directives that were pertinent and applicable when the balancer was put on
the market and that entail the CE marking of the product.
Intended conditions of use
The balancers are designed to balance the weight of tools and utensils in general and are to be used by one operator at a time. The
balancer may be used in an assembly line, in single workplaces, in professional or private environments, as a hobby, etc.
Always operate, inspect and maintain this balancer in perfect working order in accordance with all regulations pertinent to
balancers, tools and workplaces.

Technical specifications

Tube internal diameter: ................................................................................................................................................. Ø 6 mm (Ø 8 mm - 9203)
Max pressure: ................................................................................................................................................................................................ 8 bar
Max temperature: .......................................................................................................................................................................................... 50°C
Air inlet/outlet fittings: .............................................................................................................................................................. G1/4 (G3/8 - 9203)
Pressure loss inside balancer tube with reference to airflow:
Airflow (nl/1')
Use contraindications
Do not use the balancer in environments with potentially explosive atmospheres.
Do not permit children or people under age to use the balancer.
Do not work, transit or linger underneath the balancer.
When using balancers, always fully and duly comply with the standards and laws in force in the country in which they are used.
TECNA S.p.A. will not be held liable for any damage or problems caused by customers using these balancers for any other application.
Choosing the balancer
The overall load to be balanced must fall within the balancer's minimum and maximum load-bearing capacity.
Starting up the balancer
Assess the range of the work area and, if need be, hang the balancer on a carriage to be able to use it properly in an area wide enough to
carry out the required activities.
If screw-fixing devices are used to install the balancer, use self-locking nuts, split-pins or other safety systems.
Always connect the safety suspension S, using exclusively the supplied standard fittings (Fig.1), to a suitably sized support.
The safety support MUST NOT BE the same one used for the main suspension A (Fig.1). If the main suspension breaks, the max falling
distance must not be more than 100 mm. Tighten the nuts of the clamps 21215 (Fig.1) at a torque of 2 Nm.
To avoid anomalous wear, the load must be applied vertically and in any case the tube must be free to line up with the direction of the load.
Connections
- Connect the tube 23 Fig.2 to the nipple 16 Fig.2
- Connect the compressed air feed to the tube nipple 23 Fig. 2
- Connect the tool to the nipple 21 Fig. 2-4
Using the balancer
Grip the tool hanging from the balancer and carry out the required operations. Then accompany the tool until it balances, on the vertical line
of the balancer, and release it.
The tube must never be unwound all the way: its work travel must end at least 100 mm before it reaches the lower limit.
If need be, move and lock the clamp 18 (Fig.4) to stop the upward stroke.
When using the balancer, always don individual protective gear and closely adhere to the prevailing accident prevention regulations.
It is strictly prohibited to:
- Abandon the load if it is not in a vertical position
- Swing/throw the hanging load to another operator
- Move the load by pulling the balancer's tube;
- Hang loads that are not within the upper and lower ranges of the admissible load-bearing capacity
- Hang more than one tool on the balancer
366 Pressure loss (bar)
533
700
Translation of the Original Instructions
0.5
1
1.5