Warnings; Installation - Beurer SL-EM41 Bedienungsanleitung

INSTALLATION

Before installing the appliance, make sure
that none of the parts is damaged in any way.
In case of damaged parts, contact your retai-
ler and do not proceed with installation.
Read all of the following instructions with
care before installing the appliance.
- Use an air outlet pipe of the shortest pos-
sible length.
- Limit the number of pipe bends.
- Use a material approved by standards and
regulations.
- Avoid any sudden changes in pipe section
(recommended constant diameter: 150 mm
or equal surface area).
* Before installing the appliance, in order not
to damage the appliance itself, the metal gra-
se filter should be removed. Such filter can be
removed by pushing the special filter handle
toward the back side of the cooker hood and
turning it downwards so to unfasten it from
its slot (Fig.3B-4A).
Wall stirrup-fixing
* By using the special drilling jig (Fig.5X),
perforate the wall according to the pattern
indicated by the jig itself, and pay attention in
order not to damage water pipes and electric
wires. Perforation should be performed with
a Ø 8 mm wall-drill. Then insert into the
proper plastic reinforcements (Fig.5A). The
hood-bearing stirrup (Fig.5S) can be applied
by using the screws provided with the equi-
pment (Fig.5B). Now hook the cooker hood
onto its bearing (Fig.7) and then adjust hori-
zontally and vertically the position of the ap-
pliance by acting on the special metric screws
(Fig.9V,T).
After the appliance is adjusted, fix it by inser-
ting and tightening the safety screws proper-
ly (Fig.5C) Mod. SM - SL. On the modular mo-
dels standard and luxury version, after fixing
the angle iron on the wall (Fig.6C), hang the
module to the appropriate bracket (Fig.6S).
Adjust and block with the screws supplied
(Fig.9V-T). Insert the screws to block the mo-
dule (Fig.8A).
Fixing the ornamental chimney
* Before fixing the chimney, place the electric
feeding equipment into the ornamental pipe
and provide it with a hole for the air outlet if
the appliance is used in its sucking version.
Warning!
Before connecting the flexible exhausting pipe
to the motor, make sure the stop valve, which
is on the air outlet of the motor, can swing.
* INSTALLATION S10 - P127 - P128
For the models S10, P127, and P128, after
having realized the holes following the dril-
ling jig (draw. 5A part 1), insert the nogs and
use the screws you can see in drawing 5A part
2. Hook the cooker hood and screw it making
sure that the unit is perfectly flat. In order
to complete the installation, insert the two
fixing screw in the back side of the unit insi-
de the holes you have already realized (draw.
8A part. 3).
Sucking version
* Fix the pipe-bearing stirrup (Fig.10Y) to the
wall or ceiling by using the proper reinforce-
ments and screws in equipment. Connect the
cooker-hood flange with the evacuation hole
by using a proper pipe.
(For versions with display only) Lift the lower pipe
until the cable strap coming out of the sucking
unit is uncovered and connect it to the display
cable strap. Put down the lower pipe while paying
attention it is being properly introduced into the
hood. Perform the electrical connections. The
superior end of the pipe is to be fixed laterally
to the pipe bearing (Fig.11Y) by using the two
self-threading screws. Now mount the inferior
chimney by inserting it through the front side of
the cooker hood and then turning it down until
it is fixed inside (Fig.11).
Filtering version
* In the filtering version the air deviator is fixed
through the screws supplied (Fig.12), by using
the holes which are on the back of the upper
telescopic section. Connect the flange of the
appliance with the air deviator through an ap-
propriate pipe. Connect the appliance with the
electric mains. (For versions with display only)
Lift the lower pipe until the cable strap coming
out of the sucking unit is uncovered and con-
nect it to the display cable strap. Put down the
lower pipe while paying attention it is being
properly introduced into the hood.
Fix the upper chimney as indicated in bic. 11.
13