V2 VEO-RFE Serie Bedienungsanleitung Seite 13

To add another transmitter TX2 to the control unit it is necessary
to use a remote control previously stored (TX1) and proceed as
follows:
1. DUO multichannel only: press several times the key SELC of
the transmitter TX1 until displayed the channel stored.
2. DUO multichannel only: press several times the key SELC of
the new transmitter TX2 until display the channel to be stored.
3. Take the roll-up shutter to half its way with TX1.
4. Set to ON the switch 1 of the transmitter TX1.
5. Press and keep pressed for about 5 seconds the key PROG of
the TX1 until the motor starts to move.
6. Release the key PROG, the motor stops.
7. Press the key UP or DOWN of the TX2: the transmitter is
stored with the same logic of the TX1.
8. Set the switch 1 to OFF.
Switch 2: storing of the transmitters and
selection of the mode rolling shutter
To store the channel 1 of a transmitter TX1 in a blank control unit
1 controlling a roll-up shutter proceed as follows:
WARNING: the first transmitter stored fixes the direction of the
motion of the motor.
Repeat the procedure described for switch 1 using, however,
only switch 2
Switch 3: deletion of all the stored
transmitters
To delete all the transmitters stored on the control unit it is
necessary using a remote control previously stored and proceed
as follows:
1. Supply power only to the motor to be programmed
2. DUO multichannel only: press several times the button SELC
on the transmitter until displayed the channel stored.
3. Position the roll-up shutter at the mid-height.
4. Set on ON the switch 3 of the transmitter.
5. Press and keep pressed the button PROG of the transmitter
until the motor moves in both the ways for 1 second, showing
the end of deletion.
6. Release the button PROG and set on OFF the switch 3 of the
transmitter.
To delete all the codes by means of a transmitter non-stored,
proceed as follows:
1. Position the retractable at the mid-height.
2. Switch off power supply of the system.
3. Set on ON the switch 3 of a transmitter.
4. Press and keep pressed the button PROG.
5. Supply power only to the control unit on which to make the
deletion: after about 1 second the motor moves in both the
ways showing the correct deletion.
6. Release the button PROG and set on OFF the switch 3.
Switch 4: programming of the upper
position of end-of-stroke sensor
To set the upper position of the end-of-stroke sensor on a roll-up
shutter equipped with lock on the upper side it is necessary to
use a remote control previously stored and proceed as follows:
1. Supply power only to the motor to be programmed
2. DUO multichannel only: press several times the key SELC of
the transmitter until displayed the channel stored.
3. Take the roll-up shutter to half its way by the keys UP or
DOWN
4. Set to ON the switch 4 of the transmitter
5. Press and keep pressed - for about 5 seconds - the key PROG
of the transmitter until the motor, moving for 1/2 second in
both the ways, proves it is entering into programming phase.
6. Release the key PROG
7. Press the key UP: the roll-up shutter goes up at normal speed
8. Once in contact with the upper lock, it stops and memorizes
the position
9. Set to OFF the switch 4 of the transmitter
To set the upper position of the end-of-stroke sensor on a roll-up
shutter without lock on the upper side, it is necessary to use a
remote control previously stored and proceed as follows:
1. Supply power only to the motor to be programmed
2. DUO multichannel only: press several times the key SELC of
the transmitter until displayed the channel stored
3. Position the roll-up shutter at the mid-height
4. Set to ON the switch 4 of the transmitter
5. Press and keep pressed - for about 5 seconds - the key PROG
of the transmitter until the motor, moving for 1/2 second in
both the ways, proves it is entering into programming phase
6. Release the key PROG
7. Position the roll-up shutter in the UPPER position desired using
the UP and DOWN buttons. To regulate it precisely, press the
PROG button when the motor is close to the limit switch. the
motor will start to move in jerks
8. Press the key STOP once reached the required position: the
motor stops and proves the correct storage of the
end-of-stroke with a 1/2 second movement first downwards
and then upwards.
9. Set to OFF the switch 4 of the transmitter
13
UPPER
POSITION
MIDDLE
POSITION
LOWER
POSITION