Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Temperature/Climatic Conditions
This device may be used in normal climatic conditions within a
temperature range of +54ºC to -40ºC; it is not intended for use
outside these limits. Harsh environments may produce a
harmful effect.
Electrical Hazards
Due to the highly conductive nature of the materials used in the
construction of this device use Extreme Caution when working
near unprotected high voltage sources. If in doubt, ask!
Use caution when using the equipment around moving
machinery.
Chemical Contamination
Avoid prolonged exposure to corrosive chemical reagents. If
contamination occurs refer to Cleaning and Disinfection.
Sharp Edges, Abrasion, Cutting
Wire rope or webbing should not be allowed to pass over a
sharp edge without an edge protection device in place. In the
event of a fall arrest, the wire rope or webbing may be
damaged.
General Operation, TORQ Inertia Reel Fall Arrester
The mechanism in this device is activated by centrifugal force
acting on the brakes. This action is produced by the inertia of a
fall rapidly spinning the internal drum which in turn causes the
brakes to lock and arrest the fall. Slow reeling of the line will not
activate the brake. If the brake locks – due to a fall – the
mechanism will reset if the load is removed. In a fall arrest
situation the mechanism will limit the force acting on the body
to less than 6kN.
Compatibility of Components
This device may only be used with appropriate items approved
to the requirements of CE certified PPE in line with the
requirements of the PPE Regulation (EU) 2016/425 and the
American National Standards Institute (ANSI).
Anchorage Point
Select a stable anchorage point with a minimum strength of
12kN (e.g. I beam, RSJ, Eye Bolt or Tripod).
Pre-Use Inspection
If the device is known to have arrested a fall it must be
removed from service immediately, marked or tagged as
'UNUSABLE' and disposed of or serviced in accordance with
the manufacturers recommendations.
Before each use check (a) that the brake operates correctly (b)
that the block is securely anchored level with or above the user
(NEVER below) (c) that all components to be used in
conjunction with this device are approved and in good condition
(d) avoid where possible anchoring the device in such a
position that could result in a 'pendulum/swing fall' (this may
occur if the device is positioned at > 30º from the vertical in
relation to the end user).
Extend the wire rope or webbing fully (wearing suitable
protective gloves) and inspect along its length for damage,
such as (a) broken wires (b) frayed wires/webbing (c) soiling
and/or corrosion (d) kinks and twists in the wire (e) inspect the
swage/stitching for damage, cracks, etc. (f) check the
connector(s) being used as per the User Instructions supplied
with the connector (g) check that the Overload Indicator is not
exposed (red line on karabiner).
Retract the wire rope or webbing slowly; during retraction give
a sharp sudden tug in order to activate the braking mechanism.
This check should be carried out along the full length of the
rope or webbing at approximately 20% increments. If the
braking system is not activated or if any of the above criteria fail
then the device must be removed from service.
Check the device housing for signs of mechanical deformation,
cracks, or chemical contamination and/or other defects. Check
labels and tags for absence or illegibility.
This device must be used by persons who are medically fit to do
so. If you have any medical condition, are recovering from any
medical condition or suffer from any physical or mental
disability you must seek professional medical advice before
using this arrestor block.
In Use
Avoid the risk of a 'pendulum/swing fall' injury by working
wherever possible as close to and directly below the anchorage
point.
Ensure there is sufficient clearance below and around the user
so that in the event of a fall obstructions (such as the ground)
may be safely avoided (3m + height of user).
If used on the horizontal or incline, ensure the hazard of a
pendulum fall is considered and ensure sufficient fall distance
is correctly calculated. If in doubt contact the manufacturer.
This device is of sturdy construction, however, all items of PPE
should be handled with care and not dropped. When in use,
care should be taken to avoid damage, which may be caused
by items coming into contact with the device and the fall arrest
system.
This device is designed to protect ONE person. Only ONE
person may be connected to this Fall Arrestor Block at any
time.
Attach the devices line connector to the D ring on the users
harness marked with an 'A', either front sternum or rear dorsal
for fall arrest or extended overhead attachment point for
rescue and recovery operations.
Although this device will function horizontally, extreme caution
must be practiced when using the device at more than 30º from
vertical (see above).
Uncontrolled reeling may result in lock up. The wire rope must
be paid back into the device slowly. In the event of the lockup
consult the supplier or manufacturer for advice.
Warning
Werbung
